-
Smart schedule not working but booster working.
Had this a couple of times now where my smart schedule doesn’t turn the boiler on (despite it saying on my phone that it has), but if I then go to boost the heating the boiler immediately turns on. Not sure what’s going on as the smart schedule has worked fine for ages and ages…any help would be great as it’s driving me…
-
Tado TRV - Water droplets in battery area
Hi, I have Tado TRV's on all but one rad in the house, the other morning went into the front room to find it at around 25deg. Checked what the Tado app and valve was indicating, which was OFF, as per my schedule. Took the Tado off the rad to discover water droplets on it and in the battery box. Dried it all out and put it…
-
New installation
Good evening all I am a novice here I want to upgrade to a "smart heating system" I currently have an Ideal Combi boiler A honeywell wired thermostat. My knowledge here is zero. Can I have smart radiator thermostats on say the 2 upstairs bedrooms, but not the bathroom (small in size) And no smart radiator valves downstairs…
-
Thermostat Overswing
I have recently installed a wired thermostat to work in relay mode, but it doesn't switch off at the set temperature, but 1º above. Not a huge issue, but it's not working as described, so I've had to set the threshold lower. Is there a way to make the thermostat switch at the temperature it was set at? I've looked at the…
-
2 weekly schedule
My kids are at home In a 2 weekly cycle. So week 1 they are in on wed, thurs, Friday and week 2 on wed, thurs,Friday,sat,sun etc. All smart thermostat systems are based on weekly schedules.so for the even weeks I am ok but for the uneven weeks I need to switch off manually. Could tado become the first with 2 weekly…
-
Cannot find config for my room therostat
Hi I have bought the tado wired smart thermostat V3. The idea was to replace the room thermostat for my Ariterm Biomatic +20 boiler. The factory thermostat can set the desired temperature, measure the room temperature, display outdoor temperature and display alarms from the boiler. I'ts the same thermostat that is used for…
-
How long does it take for tado support to respond?
I need help with changing my boiler flow temperature and submitted it to tado about 3 days ago but I still haven't had a response. How long does it usually take?
-
Design question - underfloor heating - 2 zones
Hi all! I have underfloor heating in my main apartment. Gas boiler sends hot water to 2 water manifolds each having a circulatory pump. The first manifold has 6 water circuits and the second manifold has two water circuits. What would be the best way to control heat delivery and temperature to both zones independently…
-
Local Access and Control of Tado Heating System
In the event of an internet outage, of which there could be many reasons, my Tado heating system which uses smart TRVs, becomes entirely unusable and the valves stay in the position set when the outage occurs. In my case, the valves were off/frost protection and will remain so until my internet is restored, which due to…
-
Room displays as always manual controlled (history graph)
Hi, so I have a few rooms (with individual TRVs), central heating, and all works fine. All rooms have a schedule and away mode. That works fine too. And then there is the bathroom. The history graph shows the pointy finger icon (manual mode I think) 24/7. There is no away mode, no switch to night mode, nothing. However, as…
-
Tado turns on radiators in boiler but not hot water
Hi all, i have recently installed the tado with extension kit in the vitodens 100 b1kc, unfortunately, it seems unable to change the hotwater settings. I can't get hot water out of the faucets. When disconnecting the tado and regulates itself, it seems to work all fine. It is wired up correctly over opentherm. Any ideas?
-
Heating goes off automatically
Hello, I observed in the last 3 days the heating it's turning off sporadically even If I did not set it so. Seems it follows the smart schedule which I am not able to delete it. I just wanna set it manually and turn off it manually as well. I tried to delete the block from smart schedule but it goes to 18 degree but it's…
-
How to re configure main thermostat when replacing a heater
Hello. I'm planning to change my heater soon. What is the procedure to follow to reconfigure Tado to control a new heater?
-
Smart Thermostat replacing a Danfoss TP7001m timer/thermostat
Hi can i switch over a Danfoss TP7001m timer/thermostat to a tado Smart Thermostat, I removed my TP7001 to replace it with the Tado controller and the wiring looks different, I expect i need to change the back plate but don't know how to wire it up as the wiring labels are different, Thanks Michael
-
New Set up Help - Heating always on.
Hi All, Just wondering if I could get some advice please, as I only have the evenings to try and solve this due to work. Basically I live in a flat and believe I have a S Plan set up, due to having two valves in the utility. I bought the V3 wireless kit from Screwfix to have a wireless thermostat. I used to have a wired in…
-
Virgin Hub 5 Tado bridge issue
Hello, My Tado bridge isn’t connecting to the internet. I’ve reset it multiple time, I’ve also factory reset the router but nothing has worked . I have a virgin hub 5 router. Please help :-)
-
Stop starting heating in the morning
Hello, my TRVs start at 06:30 in the morning as per configured schedule and stop at 21:30 in the evening. Let assume it is night, after 21:30, and the TRVs are already in OFF mode. How can I avoid to switch to ON the next morning without configuring a new schedule?
-
geofence per room
i know it has been in some other discussions but i really like to have geofencing per room as so many users we have rooms (offices) that only need heating when the certain people are "home"
-
Strange behaviour during smart schedule
Do you have any idea why there was a switch from smart schedule to manual control today that caused overheating? No one manually changed the temperature either on the thermostat or in the app. Thx
-
Tado smart thermostat says heating off but boiler won't turn off
Tried resetting wall control and pressed pairing button on sensor. Turned boiler off then on. Its a sensor attached by wire to the router. it was working until plumber replaced a motorised valve. Now won't switch off and can't reduce temperature. Email support abandoned me
-
Are 3 Zones possible???
I have just moved house where i had the extension kit wireless stat and x2 TRV's. My current house has an upstairs controlled by a thermostat and downstairs on a separate circuit controlled by a thermostat, and also hot water on another circuit. Tado are telling me that 3 zones cant be controlled, but I have read that it…
-
Struggling with the Last part of my install
Hi all, Previous setup Split Level Thermostats/Controllers (Danfoss TP4000) Ideal Logic Combi ES35 Installed I have installed the v3+ wireless kit to replace the downstairs termostat I have installed the Wired thermo upstairs. The Issue The heating upstairs is working perfectly, I can control the boiler and temp from…
-
Compatibility Buderus Logamax Plus GB162
Hi, I own a Buderus Logamax Plus GB162-35 V3 driven by a wired thermostat RC35. I also have an outdoor temperature sensor. The boiler heats water for the radiators but also domestic hot water. The domestic hot water is stored in a 200 L tank and it circulates in a water loop on a weekly schedule. I consider to replace my…
-
Can I replace an existing wired thermostat with tado wireless starter kit + extension
I have a honeywell wired thermostat controlling my s-type heating system. I want to replace/bypass it and use a tado wireless thermostat to control the heating with the wireless extension kit controlling the hot water system. Do I need to buy additional bits to do this? Do I need to return the wireless tado and buy a wired…
-
Wireless Receiver Problem
Hi, I have a problem with my Wireless Receiver that has happened today. When the Wireless Receiver requests heat from the boiler to heat the house the boiler does not start (always use to until today) then when the Wireless Receiver requests heat for the hit water the boiler does start. Had the system for 10 months with no…
-
Connect 2 zone Heatmiser UFH to existing tado
Hi all, I had the heating working fine for the past 2 years with Tado controlling unvented hot water tank and radiators while a heatmiser system is controlling the 2 x UFH zones (same system boiler). I am thinking on integrating the UFH with tado and replacing the heatmiser thermostats with tado wireless thermostats but…
-
Neeedle-Positions - HOW MANY ?
my "analogue" TRV's has got "Infinite" needle-positions.... meaning: they can control the ventil's-needle in a "step-less" way! What about the Tado's? they are digital - and they control through steps (by means of a step-motor/engine). BUT, WITH HOW MANY STEPS DO THEY CONTROL THE NEEDLE?? 4-16-256-xxx ??? My…
-
Smart Wireless Thermostat - Spare wall plates available?
I had my thermostat on the wall where my old heating system’s wired thermostat used to be but now keep it dismounted in a different room. I got the plastic stand but disappointingly it doesn’t attach to the dismounted thermostat but screws to the wall plate which is currently still on my wall. Is it possible to get spare…
-
Tado Smart Radiator Thermostat making noise after switching on
Hi, I changed all radiator thermostats with Tado Smart Radiator Thermostats, it's almost working fine but in one room I have two radiators and those two are making some irritating sounds. It's not the motor noise that opens or closes the valve, but something like a tick-tick sound and it continues during the heating. I…
-
Starting from scratch
Hi all, I'm in the fortunate position to be establishing my heating system from scratch, and i'm wondering if tado could work with my intended set up. System boiler and 210l Indirect unvented gledhill hot water cylinder 12 radiators across 3 bedrooms and one bathroom, 3 - 4 sinks 50 sqm of wet ufh in one open plan kitchen…