-
Strong fluctuations in temperature
I am using tado in combination with an Elco Straton boiler. The temperature in the rooms shows very strong fluctuations, and deviates from the temperature set in tado. This is the case in all rooms. In the graph below, the set temperature is 19 degrees, but the temperature fluctuates between about 16 degrees and 20…
-
Replacing stc9004c and Digistat SCR
Need advice on how to replace the STC9004C and Digistat SCR currently connected to my system through the Honeywell Sundial wiring system. I did replace the stc9004C and the hot water worked but not the CH, as I feel wiring available from.Digistat ScR needs to be connected to Tado, but not sure how to as did t wanted to…
-
Potential Outage . . .
Message from tado: Database maintenance affecting the tado° app Upcoming scheduled maintenance notice We are planning a scheduled maintenance of our database. For a few short periods within this time: - your tado° app might become unresponsive. - your rooms might show an "offline" message. - the temperature changes in your…
-
How can extend the range of the system?
Is there anything thing I can do or buy to boost the range of my Tado system. I live in quite a large victorian house with 3 floors and thick walls. I cannot use Tado valves in all rooms. I have tried moving the bridge around, but if I can get a connection in one place, I loose it in others. Is there a third party device…
-
Boiler stops snd starts when temperature reached
Wired smart thermostat When my room gets to the set temperature my boiler keeps starting and stopping very quickly obviously this isn’t economical it’s extremely difficult to maintain a good average temperature in my bungalow .
-
UFH and wireless vs wired thermostat
Hi, I have and Vaillant new combi boiler for hot water and heating my apartment which has 4 rooms, 3 with radiators each with a tado smart TRVs and then our new extension that has water under floor heating which is controlled via a tado wireless thermostat. All 4 rooms are setup and controlled separately via the Tado app.…
-
Device communication failures
Over the past few days all of my devices are being extremely slow or non responsive. If I manually change the TRV temp It’s not feeding back to the app. Ultimately this is resulting in heating not coming on or staying on. I’ve tested the thermostat, bridge and TRVs with no improvement. Any other ideas??
-
Tado radiator now working properly.
I have 2 Tado Radiators in 2 rooms next to each other with an open planning ( no walls in between the rooms). One Tado Radiator says its 18 degrees celcius ( heating up to 15 degrees ). The other one says it 13.8 degrees celcius. The are about 12 meters from each other. For the first Tado Radiator works as expected:…
-
Finding the right TRV adaptor...help!
Hi, I cannot seem.to identify the right Tado adaptor. The radiator valve has DN15 on the side. Help pease!
-
Suggestion for Internet failsafe
Dear TADO guys.... Could you improve the system by arranging for the extension/control box used on a combi boiler to set the smart rad valves to frost protection if the internet is down for say an hour or more automatically?
-
Auto assist message V3+
Have this message in auto assist Auto-Assist is provided to you courtesy of Apple I don't have an apple account though.
-
Bug Report: if a TRV dies while calling for heat, it continually calls for heat even in away mode
I have just encountered a fairly annoying bug with Tado. We have been out all day, and tado was in away mode, everything looked like it was off. Annoyingly though we have come home to the house heated like a sauna. I have some radiators not on a TRV, howevet one Tado TRV was calling for heat even though they shouldn't have…
-
Faulty temperature and humidity
One radiator thermostat has worked perfectly for a year but now shows the temperature of 6° C and a humidity of 76% it shows the same values whatever the room temperature or the room humidity. Consequently the radiator is permanently on as it thinks it's at the temperature needing Frost protection. So the room is hot maybe…
-
Why does the boiler come on when there is no demand for heat?
Boiler keeps randomly coming on even though on all radiators and room stats are off on the program. Mainly keeps happening at night when there is no call for heat.
-
Worcester Bosch Greenstar 42 CDI Classic
Worcester Bosch Greenstar 42 CDI Classic Installation from previous posts say 1. +/- in Tado EU extension kit to BB in boiler 2. Wire link between Ls and Lr 3. Disconnect onboard control 4.TS / HC01 / HW (x) / EK (y) / D17 Question: Is the extension kit powered by the BB boiler connections or should extension kit also be…
-
How to system the system with one smart thermostat and 3 smart radiator thermostat
I have one smart thermostat at my living room "wired" to control an Ideal Mexico boiler. if I got 3 smart radiator thermostat in Living , Dinner and utility. if the living room thermostat reach the temperature it will cut the CH. how to set the CH still working if either one of the radiator need to operate. on the other…
-
Hot water HomeKit functionality
Hi, I emailed support about this and they won’t do it. They said to create a poll to gather interest so who would like to see this? It is something I believe is a quick fix and could be easily added to the Tado functionality.
-
Danfoss TP5001B compatible wiring?
Hi, Second question on here. I have an Ideal combi boiler with two zones (upstairs and downstairs) controlled by two Danfoss TP5001B thermostats. I plan on simply swapping them with wired tado thermostats. After having a quick peak under the hood they have two wires, one wire going to the common terminal, the other going…
-
Replacing Therma txq0027
Hi all, I’ve got a new build property with Therma txq0027, multi-room. Ch1 whole house, ch2 just does lounge, which is pointless, + hot water. The wiring looks identical to fit the Tado receiver (-ch2). I’ve order a wired and wireless controller - have ch1 / ch2 linked + hw connected to receiver. Hw is working correctly.…
-
No heating
I have just installed the v3+ and the boiler will not fire up when heating is called for, hot water works fine. I replaced a British Gas wireless thermostat and programmer which was working fine, I had a new motorised valve fitted a week ago and all was fine until I fitted this at 9.30am this morning.I’ve been trying all…
-
Tado constantly firing boiler
so my smart thermostat is set to heat at 15.2 but for the last week the boiler seems to just be constantly on the thermostat now reads 23.2 and its still on. i have checked this against a thermometer in the same room and its reading the same. i have had the tado for over 4 years but now its just started doing this. any…
-
1 flame icon not heating up
I recently observed an issue with my Ideal Logic Code ESP1 38 where, despite setting the Tado Pro app to 80°C, Opentherm doesn't surpass 60°C. While this may seem positive, I encountered a problem when any radiator, marked with 1 flame in the app, triggers the boiler, causing non-Tado TRV radiators to heat up. To be clear…
-
What setup works best in this configuration?
I have one +/- 55 m2 open area with the following layout. On the right is the entrance with a door and a window. On the left a large sliding window towards the yard. I have 3 radiators, all three the same size and all three have the smart radiator heads. Currently, I have 3 rooms set up, Office (thermostat + radiator head…
-
Need to know what is the best bundle to buy to my 20 years old boiler and cylinder
Hi Experts, I am planning to move to tado. I kindly need to know which tado system would work best to control hot water and heating to the maximum benefit. I have a 20 years old heating system. This consists of: - Potterton kingfisher MF LTX0346 Boiler - Vented hot water cylinder 1500 X 500 + Honeywell L641A1039 Cylinder…
-
wiring new Tado thermostats
Hi, I've bought new thermostats, but Tado don't provide install instructions to switch from the existing Therma thermostats as they aren't recognised by the online tool. Rather than wait 4-5 days for tado support I thought I would try here first. Wiring into existing thermostat attached. Not using with H/W Any ideas?…
-
New Install, heating not working, spare wire behind the old board not connected
Hi I have tried to install wireless controller where previous controller was danfloss FP715si. I marked up all the wires and took off the old controller and there was a wire behind that was not connected to anything. The heating does not work, after trying to reinstall old controller again the heating still doesn't work…
-
Any professional installer in Falkirk area?
I have just moved into a house with a Worcester Greenstar Compact with Comfort II RF and bought the tado kit required but the installation is beyond me. Thanks in advance.
-
Thermostat stuck on downloading firmware
No meaningful solution from Tado other than change batteries and restart. upping the temp on the app does not put the heating on as the command is not getting to the thermostat. been like this 4 days. I have unplugged the bridge and reconnected and taken the thermostat nearer the bridge. any ideas on a fix
-
Installation replacing 3 channel controller
Hi all, I'm looking for some advice. I have a new build property with a Logic H24 boiler in the garage and what appears to be a manual controller (for Frost?) next to it. The opentherm pins appear to be bridged together and on the left hand side a single black cable goes into SL1 IN alongside the usual Earth / Neutral /…
-
Wireless and wired thermostat working together?
I have a tado Starter Kit - Wired Smart Thermostat V3+. It's great, but the thermostat location is above a radiator and this is messing things up. Moving the thermostat would be really difficult and probably expensive. So, does tado have a product where I can send temperature data to the thermostat from another device,…