-
Tado system heating without needing to
Hi all I’ve had my system in for 18 months now in the upstairs of my house, 3 bedrooms Bedroom 1 one TRV Bedroom 2 one TRV Bedroom 3 two TRVs All 3 bedrooms are set to 18 degrees and not asking for heat, however there all up at 22 degrees and the boiler is constantly running and subsequently heating the two towel rails…
-
Tado X Thermostats Disconnecting.
I installed Tado X yesterday. As I purchased a number of kits I have the following. 2 Thermostats 1 Bridge 2 Wireless REcievers 20 Tado X Thermostats. Worked fine overnight, but now 10 of the Thermostats are off-line and not connected. This would make the system unreliable for me as when I travel the risk of not having…
-
Wireless Receiver and Internet Bridge keep dropping out
Hi, I posted a question previously about my Internet bridge and wireless receiver losing connection but my trv's still being active and heating according to the schedule. They keep dropping out, which means we are unable to adjust temperatures until everything is reset and connectivity is resumed. The Internet bridge is…
-
Smart thermostat won't pair
I have just moved into a house with a Tado smart thermostat, extension kit and internet bridge, and basically can't get any of it to work reliably. The app says all of the devices are connected, the current temperature is 15 degrees and it is set to heat to 19 degrees. The app says it is heating, but the boiler is not…
-
Tado signal to boiler not always working
We have had a Tado for several years but just these last few days it would seem the boiler is not receiving the signal
-
Is it possible to configure a fixed IP address in the Tado internet bridge ?
I control Tado via Home Assistant, and when the IP address changes, the device becomes unavailable in Home Assistant, because sometimes it gets another IP address from the router. The router is configured to give the Tado device a static lease, always the same IP address, but sometimes, it gives it another IP address. So I…
-
Tado X wiring
Hi , I'm replacing my nest heatlink with the Tado X. In the installation guide it shows two wiring options, neither of which match the existing wiring on my nest heatlink. The two wire option shows the wires in OT1 and OT2, my heatlink is wired in OT2 and OT3. How do I wire the Tado X? Thanks for any help.
-
Guide to EnergyIQ for oil boilers
Below is a step‐by‐step guide you can use to calculate your heating consumption in kWh and input it into Tado’s Heating Bill (Energy IQ) section for an oil/kero boiler My tank uses Kingspan wireless monitor as you’ll need a reasonable accurate view of what is in your tank. Estimating based ok % may work but won’t be as…
-
Combining existing tado TRV radiator setup with new heatmiser UFH.
I currently have a tado wireless receiver instructing the condensing boiler to fire up when the TRV temperature sensor says so. My current setup is as shown below. I'm now adding 2 UFH zones with a manifold controlled by a heatmiser UFH wiring centre. With the addition of the underfloor heating, I would like to use the…
-
Why do I get different humidity value in the tado app and in HomeKit?
I have a tado smart thermostat, it is turned off now. Currently in the app I see 58% humidity but in HomeKit only 54%. The temperature looks like to be correct.
-
Help replace my heatmiser?
Hi all I'm sorry for probably quite a basic post, but I seem to have gone round and round trying to work this out, and be getting nowhere. Basically, I've just had work done to my house, and have now got: -pressurised hotwater cylinder (megaflo equivalent) -ecotec system boiler -heatmiser neo wired hot water controller by…
-
Spare adaptor for V radiator thermostat?
One of my v thermostats showed a spanner error. Through swapping it with a different radiator I isolated the problem as being with the adaptor or the bottom part of the thermostat that the main device connects to, ie the bit that you fit around the radiator. Question is - how do I get a new one of these to see if that…
-
Zone Controller Controlling All Rooms Instead of Just One
I've just installed my Tado X system; there are 12 radiators with Tado Smart Radiator Thermostat Xs and and one Tremperature Sensor X, which I have set to be the Zone Controller for the lounge with its two radiators. All other rooms have had their Zone Controller set to None. I carefully set all Radiators to different…
-
Another Tado X hot water ask for help
Hi everyone, I have a Logic S18 boiler with hot water tank upstairs. It was controlled by a Danfoss TS715si controller before I switched to Tado V3 and now I decided to “upgrade” to Tado X, with two wired temperature controllers and wireless receiver along with some TRVs. I’ve gone through the installation with help from…
-
Tado X - Which Starter Kit and Wired or Wireless Room Stat
I’m planning on installing a Tado X system in my home. The present system is based on an Intergas Compact HRE 24OV gas boiler with conventional programmer and wired room stat (which happens to be in a useless position in a 1m x 1m central hallway, but more of that later). Hot water is supplied via the boiler into a…
-
Worcester greenstar 8000
I have recently wired up the tado V3+ to my boiler but it's not controlling it. Do I need to disconnect the existing RF receiver?
-
Vaillant connection with Tado
I am connecting my tado° Wireless Smart Thermostat Starter Kit V3+with boiler Vaillant ecoTEC pro 28H combi. I want to use eBUS connection on my Boiler side. When connecting with my receiver should I connect it to CH COM and CH NO, in a same way as if connecting with RT in boiler. Also, it seems that if using eBUS I would…
-
Which system for Vaillant ecoFIT pure 418?
Hi, I was pondering between Hive or Tado and inclined towards Tado as it seems to be cheaper and can set min max temperatures. Below is my system: Vaillant ecoFIT pure 418 system boiler with only 6 radiators S Plan motorised valves to serve Hot Water cylinder and boiler The zone valves are switched by wired room thermostat…
-
Glow worm ultimate 3 30c open therm
Hi all, Would anybody be kind enough to confirm wiring for the above boiler for opentherm? Currently wired with dumb thermostat. Assume I should be using the “bus” as opposed to the RT and 24v terminals? Ie CH COM -> BUS CH NO -> BUS Does the B.off link need removing? Thanks
-
Upgraded to Tado X, lost lifetime Auto-Assist!
I took up the discount offer to upgrade my original Tado to Tado X. The email offer says: "As a long-time customer, you can take your free Auto-Assist with you when you switch to tado° X. Your Auto-Assist will work as soon as you've connected the tado° X Bridge. Please note that the transfer is only possible if you…
-
Post Electric Outrage Issues
We recently had a power outage and post electric outage my Tado does appear to be properly heating up the house and even the hot water has glitched. Some of the radiators are working a little but others aren't coming on at all. What can I do to fix this issue?
-
Automating A/C
Hi, I have a Tado device that controls my split a/c and heating unit. For a/c during the summer, I have not found the "smart schedule" offered by the Tado app to be useful. It doesn't work to have the changes happen at set times per day; they need to be based on inside and outside temperature. I wrote an AWS lambda…
-
Heating not coming on
Hi all. I went away for a few days, and now my heating is no longer working. I have changed nothing - only turned it off in the app while away. The hot water is working, though perhaps not coning on right away when I switch to it. I have a system boiler, a wireless receiver, bridge and various wall thermostats and radiator…
-
API device code grant flow assistance
Hi I use the "password grant flow" method of accessing the Tado API using code built on an ESP8266. I have received a mail telling me that I will now need to move to a "device code grant flow" authorisation process, and example of the process is given. When I follow the example I get to a point which shows this request:…
-
System boiler with Opentherm PDHW - X PLAN
I want to know if people are using Tado X with opentherm on a system boiler and tank using opentherm? from my understanding this needs to be configured as PDHW. If you have this type of setup work I would love to see what you have and how well this is working.
-
energy efficiency with Tado X relay on/off vs Tado V3+ modulating/opentherm
I purchased a Tado X wired thermostat along with 12 Tado X radiator valves, assuming they would be compatible with my system in the same way as the V3+ version. However, I discovered that my Ariston boiler uses BridgeNet instead of Opentherm, and the X version isn’t compatible with my boiler’s digital interface. As a…
-
False Low Battery
Trv packed up with low battery notification after only 25 days. Nothing wrong with batteries, having removed, tested and refitted them the status is showing as good battery and fully working. Was this a physical loss of battery connection or a problem with the Trv software?
-
Opentherm control of system boiler
Hi Viessmann system boiler - 4 pipe installation (one heating circuit & one hot water circuit to a hot water cylinder) Opentherm control (via EU wireless extender) seems to be working well and flow temperature optimization seems to have the boiler modulating nicely. I can set/schedule the hot water temperature via the Tado…
-
Client Id for New Authentication Process
In your https://support.tado.com/en/articles/8565472-how-do-i-authenticate-to-access-the-rest-api it mentions a Client Id code. Is this a a fixed code or does it change per user / system? If the latter then how does one find it?
-
Radiator Thermostat
My Radiator Thermostat keeps being offline, even though I changed to new batteries in the Radiator Thermostat. Any suggestions?