-
Missing Features Tado X Early Start - Profiles Scheduling
I would like to know if early start can be available again for Tado x? Is there no way to store programming profiles? So that the user can quickly choose from his stored profiles instead of having to change everything manually and having to manually write down the profiles? If I am on vacation and want a different profile…
-
Hi, is it normal to have to tap the tado control to get the relays to let go?
Love the product and it's been a steep learning curve. I eventually found a temporary work around for a fault but I don't think it's a long term solution. Twice now the central heating pump and boiler has remained switched on even when the controller lights indicate that it should be off. Regardless of any reboot or reset…
-
Who to wire to Installing Tado Starter V3+ kit with Worcester Bosch Greenstar 30 si?
Who to wire to Installing Tado Starter V3+ kit wired with Worcester Bosch Greenstar 30 from Drayton thermostat? Do I put it on a digital ( N with - and L with +) and any additional wires I need to isolate? Thank you in advance for your help.
-
Lost the case screw at the bottom
I lost the tiny case screw from under the Tado. Anyone know how to get a replacement? Or what size it is? it’s not essential, but it’s annoying that it disappeared!
-
Tado X Firmware
What is the latest Tado X Firmware for all the Tado X devices? Is there a web page that lists all the firmware, and what changes were between versions?
-
How to force thermostat to obey schedule after turning off manual control?
This is schedule set for thermostat controlling UFH: Sometimes I set temperature to 21C (seen as manually - Alexa automation). Then, after some time, Tado goes back to schedule (turns off manual control), but does it faultyly - "thinking" that different temperature is scheduled than it actually is: Do you know what to do?
-
Desperate for an answer on TRV calling for heat
I reached out to support but frankly the response is beyond poor and taking over a day. I have 5 TRV's upstairs and downstairs I have 5 wired Thermostats. When the TRV's upstairs need heat, no call to the boiler is made and they stay cold unless one of the thermostats downstairs is calling for heat. I ready through the…
-
Veissman Vitodens 100-W wb1c and Tado v3+ not communicating
Hi, we've had the Tado v3+ installed for about a month and no matter what we do, the Tado will not control the boiler. We've disconnected the previous thermostat which was the Veissman Vitotrol RF wireless. That's now dead and buried. Various " experts" have suggested several wiring configurations and things to try but…
-
Are the Danfoss RA-C2 Compatible with TADO X?
Hi, Are these compatible with TADO X Valves? https://www.screwfix.com/p/danfoss-ras-c-white-angled-thermostatic-trv-lockshield-15mm-x-1-2-/49331 I can't get a firm answer from the compatibility and a lot of the valves are now superseded
-
Unable to add devices to app through Matter
Just received my Tado Wireless Receiver X + Wireless Temperature Sensor + 8 RTV's. Installing the Wireless Receiver worked fine (it seems). But none of the other products seem to be able to connect through Matter with me. Ipv6 is enabled on the router, but it always stops at "generating Matter credentials". Multiple…
-
I want advice about what Tado parts I need and how to wire them to a 2 port 'S' plan system
I am trying to get variable temperature control and timing from a Tado controller. Present system: Thorn EMI Olympic Boiler 38/50B (old but I am told simple) Grasslin/Towerchron QE2 electronic 7 day timer (With a back plate) Satchwell wired hall thermostat The system has 2 motorised valves, hot water cylinder with a…
-
Issues and solution for setting up tado with 3rd party integrations
So I've had my fair share with setting up tado and wanted to share my problems and solutions. Note that I have a Unifi dream machine as router, complicating things a bit more (as it turns out). The core problem I had were: Unable to connect the Tado X bridge; Device linking button missing; Unable to link to third party…
-
Why are my Thermostat X listed as offline when connected through Nest Hub
Hi! I'm a new member and have recently begun my tado° journey by installing multiple Smart Thermostat X devices in my home. I followed the app instructions by adding the thermostats in the tado° app and then to Google Home using the Matter "Device Linking" feature. I use a pair of 'Google Nest Hub 2nd Gen' devices as…
-
How to make Tado Bridge X join an existing Thread network?
Hi! I set up Tado X in one location and the bridge joined the existing Thread network (by SmartThings hub). But in the second location there are 2 separate Thread networks. How can I force the Bridge X to join the existing network as in the other location?
-
Radiator valve temperature sensor
In an attempt to reduce the difference between the room temp and the recorded valve temp, I am trying to establish which part of the valve contains the temperature sensor. I believe there are two sensors and the advice is to have the small opening on top of the valve facing the room. Is it better to have that opening…
-
Devices missing from Tado Skill in Alexa
I have the Tado skill in Alexa working but it is missing some devices. I've tried disabling and re-enabling the skill but it's still missing the devices. Any idea how to get them added?
-
Vaillant ecotec plus and ebus
Hi there. I've recently had a Vaillant ecotec plus 835 boiler fitted. I've also just bought a tado v3+ wireless starter kit. Just going through the installation instructions on the app and it says to wire the wireless receiver to 24v=RT on the boiler. Is this correct as I thought it should be wired to - /+bus for boiler…
-
How to override resume schedule.
I want to set a time when Tado will close down a radiator at the same time every evening so it will not come on in the morning or until I turn it on manually during the day. The problem is that whenever I turn it on manually it overrides the time to switch off until I press ‘resume schedule’ but if I do that it comes on at…
-
Vsmart zero tado 10
Well what can I say. I have had a Vaillant boiler for the last 15 years and about 4 years ago it failed and as there were so many issues with the inbuilt water storage I decided as it has done quite well to buy an 800 series ecotek. As part of this process I decided to embrace modulating heating and purchased the vaillant…
-
Brand New Tado X Setup
Hi all, New to Tado and now have installed Tado X full home system. I have conventional S Plan system, Baxi Ecoblue boiler and hot water tank. I have already set-up the wireless receiver X, the wireless temp sensor located in the hallway and set-up all my smart rad valves. Everything is working fine, my hot water control…
-
Moving from Nest to Tado, help needed
Hi all, My current setup is Nest 3rd generation using a wireless thermostat and a combi (Worcester Bosch) boiler. I want to move to Tado: for the smart radiator thermostats. The radiator valves are easy enough to buy/install, I can do those myself. But I do not understand how to replace the Nest heatlink thing with Tado.…
-
Tado randomly switching off my heating
Hi guys Recently my tado started switching off my heating. It happens randomly at different times and days. Usually every day or every other day. Whole house heating (I have 2 thermostats covering 2 zones) will be switched to frost protection and won’t switch on until I go to the app and click on resume my schedules…
-
Smart thermostat turning itself off
Hi all, My tado has been working fine for over a year. Over the last few weeks however it is turning off before my rads heat up. It also happens on manual control. It will come on and then after about 5 mins or less I can hear the relay click and it will turn off. According to the app and the display it should be on as…
-
On the Wired Smart Thermostat Starter Kit V3+ Does the bridge need a power supply?
Hi folks, little confused here. The internet bridge that connects to the router, is it power over ethernet or does it need a seperate mains power supply. It looks like the kit does not come with a power supply, if needed.
-
Heating gets stuck on “set to”
My heating gets stuck on “set to” rather than “heating to”. It’s super flakey if it moves from set to heating. Some rooms are on and some are not. Who else has had this issue?
-
Issue with creating matter link code
It took me more than 4 hours to configure tado° X as the devices were not connecting, the bridge was giving weird errors, devices were requesting a Matter bridge router, etc.. I had to factory reset the router twice. Now finally it appear everything is connected and I need to connect it to alexa and matter and I get an…
-
Energy IQ
Energy IQ needs to be flexible as not every person billing cycle starts on the 1st of the month. My billing cycle is 21st to 22nd the following month, it would be nice to have the flexibility of being able to change the date range. Without this, the data will continue to be incorrect. I'm sure it doesn't require that much…
-
Open window detection not working
Hi Open window detection has stopped working. It seemed to work 2 times. Is there a way to trouble shoot this issue? And open window detection is enabled. Also is there a way to keep the heat off for a day if I forget to close a window In the basement?
-
Fratelli TRV valve M28 x 1.5
I am interested in fitting out my home with Tado smart trvs, i currently have Fratelli TRVs which I believe are an m28 x 1.5mm thread. In your documentation, you state that these valves are not support with adapters, but other M28 x 1.5mm valves are. I would like to know why they are incompatible, do you have a dimensioned…
-
Tado and Viessmann Vitodens 100W B1KF (New Install)
Hi all, Hoping to get some help with my new install. Recently had a Viessmann Vitodens 100-w B1KF combi boiler installed. Boiler is working fine as expected, it is set up using weather compensation and I have installed the external temperature sensor. I installed the Tado V3 kit with the follwing installed: Internet…