-
Connect Tado X with Baxiroca Novanox Platinum 28/28f
Hi, I have a boiler to Baxiroca Novanox Platinum 28/28f with a control AVS77. How do I have to make the connection? Do I have to remove the AVS 77 Thank you
-
Does Nest and Tado work side by side
Hi. I recently had a tado thermostats installed. I have 3 heating zones that are controlled by Nest heat link boxes. 2 control under floor heating, and 1 used to control all of the other radiators in the house (upstairs and downstairs). I decided to get the taco thermostats installed on 6 of the 8 radiators on the…
-
Hoe to connect this „great“ product to home network?!
Hi everyone, I was planning to replace my disconnected smart thermostats with something more advanced and selected this tado product - starter kit with two termo and bridge x. In addition i bought smart sensor… finally got some time to install it all, and guess what - it has been 5 freaking hours pf attempts… to get bridge…
-
Tado and Heatmiser UH4
I am in the process of extending my Tado setup to include the underfloor heating zone we have in one room. Currently that is still controlled by an old Dataterm multi zone system. So I have a bit of a complex wiring set up, and I can't control the UFH from Tado. So I installed a wired Tado thermostat and ran a cable back…
-
Hot water command
Hi, I'm a user of tado thermostat cabled with a radiant r2k heater. As some other Italian users we have an issue with domestic hot water when the thermostat is cabled with opentherm configuration. When the thermostat work as heating the domestic hot water works too. But when the thermostat reach the temperature set, the…
-
Heating issue : VITODENS 050-W, BPJD-24 / EPH control
I’m unable to switch off the heating using the wireless sensor / app i Installed a wireless thermostat kit. The boiler is VITODENS 050-W, BPJD-24 and the previous wireless receiver was EPH. This was what the original wire config it doesn’t look like opentherm was wired when the original receiver was and from my…
-
Why is my wireless thermostat showing my house is 19 degrees? When it’s not with the heating off?
I have installed the Wireless Smart Thermostat X - Starter Kit incl. Programmer with Hot Water Control and OpenTherm on my vaillant eco tec pro 28 boiler. Is the wireless thermostat not accurate as to how warm the house is? Because it feels really cold but thermostat says 19 degrees with heating being off??
-
Is bypass valve needed with Tado X?
I currently have all 24 of my radiators set up with Tado X I'm just about to replace the boiler Auto Bypass Valve (ABV) as it seems to be stuck open. It got me thinking - with Tado controlling the boiler, circulating pump and TRVs, is there a need for a bypass valve? Is the Tado system configured so that the boiler and…
-
Do i need to replace EPH controller in order to use Wireless Thermostat.
Firstly, VERY HAPPY to have found this community, google wasn't helping much. I currently have EPH 37HW (3 channels) 1 Upstairs 2 Downstairs 3 HW. I do not use the HW zone as i have a seperate timer on my roof hot water system. My 2 current thermostats are next to the back door and in an upstairs hall way, neither are…
-
Summer room settings
Now that the nicer weather is arriving is it possible to program two groups of room settings, one for winter and one for summer? At the moment I only have one, and normally throughout the day the heating is not active. When I open the bifold doors there is sometimes a sufficient temperature reduction to activate the…
-
Multiple accounts in 1 Tado App
Being a fan of Tado, I introduced to both my kids and mother in law. My mother in law needs some assistance, and in case, I can have the control from my home. But needed an other divice, because it's not possible to have 2 accounts on the same app. Is it possible to add multiple accouts / living address to 1 app on 1…
-
Apply Flow Temperature Optimization to Multiple Tado° Thermostats (heat sources)
User Story: As a Tado° Smart Thermostat X user with multiple heat sources controlled by multiple Tado° Smart Thermostat X devices, I want to apply flow temperature optimization to more than one heat source via the Tado° Smart Thermostat X device that controls each heat source, so that I can efficiently manage the heating…
-
Multi-zone S-plan setup using Vaillant eBus...
Hi all! I am successfully running an S-plan set up using 'basic' 230V relay switching, and am really struggling to see if/how I can utilise the (more efficient) eBUS. I've tried Tado help and searching the forum but am a bit lost - can any experienced users help me? Current setup (all working nicely with 'basic' 230V relay…
-
Energy IQ cost to account for standing charge
I find the estimated gas cost estimate to be reasonably good, but the cost shown is for the consumption cost only. It would be useful for option to include the cost of daily standing charge such that the total month prediction / comparison reflects the total bill for gas not just the consumption.
-
Unable to Add Tado X Devices to Home Assistant
Hi, In the Tado app, I initially couldn’t see the device linking option. However, after performing a factory reset on all devices and re-adding them, the issue was resolved. I was able to successfully add the devices to Google Home. Apart from some connectivity issues, everything works fine there, and I can adjust the…
-
iPhone/Siri Shortcuts Support
TADO application doesn't appear in Siri/iPhone shortcuts. This application is very powerfull and, though complicated to use, can do much more than IFTTT in the Apple world. Tado must support Siri shortcuts. Homekit is obviously supported and a few (very limited) number of things can be done that way. Please support me.
-
Do I need the tado app if using Apple Hompod?
Mesh nodes, good wifi, apple homepod - but cannot get tado X to connect in other rooms. Work when I’m next to them with my phone, but am I confusing them by having the tado app on my phone? Do I need it with apple Home app?
-
Boiler pump anti seizure exercise.
So my boiler originally had pump anti seize feature, but looks loke after installation of Tado it's not a case anymore. So I'm thinking adding this feature to Tado software will be really good thing to protect users heating system.
-
Heating Activity stopped logging heating hours
Hello, I've had an issue with my app since yesterday. Although the heating has been on and the room graphs show this, the Heating Activity under Care & Protect has shown zero hours since yesterday, in both the written total and graph. My Android updated yesterday so I don't know whether his had anything to do with it. It's…
-
Can I reset the wireless receiver remotely?
Hi, We have a small annex that we rent out to guests. We are not always in the area when it is occupied by guests. (So we dont use geofencing) Our Tado wireless receiver has caused us problems on a number of occasions since we had it fitted 5 months ago. It goes off line too frequently for comfort (Every few weeks). When…
-
Merged: Enable Offline Schedule
This discussion has been merged.
-
Tado x devices added to google home but wont work with voice commands.
Hi Just installed wired tado x thermostat and 6 tado x trv I have successfully added all items ms to google home and can control via google home app. I am also able to ask google home for humidity and temperature values of all devices but i am not able to change temperature via google assistant. Whenever I ask to set a…
-
Returning tado X thermostats?
Spent three days on and off squatting on the floor trying to get these things to work. In the end I got one to work in the kitchen, where the Apple Homepod sits. Q1: I put it in the Home app and then found you’re restricted to be it being on for only 4 hrs at a time - no proper scheduling with different temperatures.…
-
QR Code generator
Hi, I have kids and the QR code stickers on the thermostatic heads won't last much (I'm already using the kid protection). Is there a way to regenerate QR code from the device number ? I have added many heads and I now save all the remaining stickers carefully, but what about the ones already lost. I would like a smooth…
-
How can I set the tariff unit rate in Energy IQ
I attempted to set this today and was unable to do so. I changed the unit to £/kWh and given my rate is 6.25 pence per kWh i tried to enter 0.0625 but the app would not accept this, turning the field red and disabling the "Save" button. In fact it would not accept anything but whole numbers which equated to Pounds per…
-
Geofencing Switch - tado X
To ignore geofencing in a timeblock on the smart schedule. Keep set rooms active when geofencing is triggered
-
Worksheet Logging of QR Codes
Hi All, I don't know if this has already been done / provided by someone else, but, whilst building my TADO system and waiting for everything to arrive (thank you eBay), I started worrying about missing/damaged QR Codes. So, I built a google worksheet that can be used to store the QR code data, and provide the QR code when…
-
Devices missing from Tado Skill in Alexa
I have the Tado skill in Alexa working but it is missing some devices. I've tried disabling and re-enabling the skill but it's still missing the devices. Any idea how to get them added?
-
trying to fit replacement wireless receiver old one stick in on position
Hi any one know who to replace wireless receiver fitted new one bur cant get it to talk to room stat
-
Heating advance
Hi, This is an old idea that hasn't occurred to Tado as yet. My old school heating controllers have always included a Heating Advance Button. It's a simple idea - if you have a day that starts a bit earlier than usual, you just advance the whole heating programme with a single click, or turn of a knob. The next programmed…