I've just installed a Tado system to run heating and hot water for the house and all is working fine. However, as part of the system we have installed, we have one large-ish room which has two radiato…
Is anyone from Tado able to confirm or deny if a manual toggle for the Home and Away mode is on the development roadmap? I accept that as I am using V3, I will have to pay for geofencing. However, if …
I started a chat with tado help about 3 o clock as the extension wasn’t cooperating. I’m still yet to get a response. I had to put all the heating back to original controls so effectively have worked …
Is it possible to use a single controller to connect both to a boiler control and underfloor heating at the same time. I.e. it can call for heat from the boiler and also turn the underfloor (electric …
hi all, my tado is only few hours in service, and i am starting to think how to control temperatures in each rooms. I have a boiler which tado is switching on and off. Hot water is then running trough…
I have a Boiler which requires one Radiator to be permanently 'on' so as to allow the boiler to circulate water down to a given temperature - normally takes about 2/3 minutes after last device has tur…
Hi, now that the colder season is coming, annoying issues with my tado system are coming up again... The main bathroom (2 radiators, both with smart radiator thermostat, it is quite a large room) has …
I've just purchased 21 x TRVs, 2 x smart stats and an extension kit but I've run into issues with the second box of TRVs in that I can't complete the set-up as the TRVs can't be assigned to a new room…
Hi - I have V3 App but would like to upgrade to V3+. I have tried to press the button on the App, but it does not work....please let me know how I can upgrade......thanks.
Hi, I purchased 21 radiator valves this week but unfortunately, the single one I purchased has a horizontal display rather than the vertical one. Is there any way to re-configure them or do I need to …
Just looking at the iOS release history and I'm kind of astounded how little has been added. In the last 12 months since 5.2 I see Redesigned homekit UI Recommendations of when to open the window for …
I have no heating and the boiler is on standby - the extension kit has been reset but the boiler comes on for seconds then goes off. I've asked tado for help but they told me to take a photo of the wi…
I have no heating and the boiler is on standby - the extension kit has been reset but the boiler comes on for seconds then goes off. I've asked tado for help but they told me to take a photo of the wi…
Evening I have just swapped my system from nest to tado, I have installed trv’s in every room and also a smart thermostat in the lounge. The problem I’m having is my trv’s don’t seem to be able to fir…
Hi there, I have had a v1 since launch but the battery in the thermostat stopped charging. I bought a new battery and that doesn't charge. Thought it was duff and got another, now that's not charging …
I have just installed the latest smart thermostat. I am confused as to what I should be seeing when I press the manual button (bottom right) on the thermostat. All I get is the actual temperature foll…
Hi, I’ve just installed tado smart thermostat V3+ (with extension kit) got it all up and running. Set the temp to 20deg! It’s now 25.5deg 🥵 and the heating is not switching off!! Can anyone help? Tha…
If the Tado boiler control thermostat is not asking for heat (low setting or frost protection) can a radiator thermostat in another room call for heat and switch on the boiler?
I have just had a new boiler installed and was planning to get my existing Tado (extension kit, room thermostat and smart TRVs) hooked up to it via OpenTherm rather than relay. My installer cautioned …
Hi all, I decided to try to use Tado smart thermostats. My current setup with an existing thermostat is simple 24V on/off control. My boiler supports support OpenTherm connection though. Will it make …
Is there a stand-alone thermometer? I want to have this in my rooms some meters away from the valve thermostats, so I can get a more precise control over the system.
