-
Tado not talking to Boilee
I have installed a V3+ starter kit to replace a Danfoss TS710 and a RET2001 connected to a Ideal logic combi esp1, all Tado equipment connected and talking to each other but when the heating is switched on there is no action from the boiler. Hot water working fine just no CH when demand from the Tado, anyone got any ideas…
-
Connectivity issues with smart radiator thermostats
I'm joining many others in my opinion that havng all radiator thermostats centered on a single Bridge is dumb and not applicable for anything but the smallest single-floor houses or appartments. I have a modular house built with reinforced concrete and have been struggling to find a placement for the Internet Bridge that…
-
Decorative TRV Valves
I have Tado Smart Radiator Valves on most of my radiators. The majority are fitted onto Danfloss TRV's (with adaptors) and work great. I am renovating my property and room by room am upgrading the radiators and putting in traditional style Milano Windsor column radiators and would like to put in decorative fittings also. I…
-
How do I change the hot water temperature through Ebus on a Glow-Worm Ultimate 30c
I have a Glow-Worm Ultimate 30c, which is a combi, wired in via Ebus and all is working as it should. The only thing I'm unable to do is to control the hot water temperature. The slider appears in the app, but the change in temperature doesn't reflect on the boiler. With Glow-Worms, if you install one of their own Ebus…
-
Energy IQ vastly underestimating heating consumption
Hi all, I've recently submitted all of my meter readings into Energy IQ for the past year, and have also updated it with my latest tariff. Despite this, Energy IQ is way off - for example, in September it's claiming I used 3.31m^3 of energy desite my energy bill (smart meter) reading 15.7m^3. Other months show similar…
-
Zones
I have two wired thermostats and one smart TRV. Downstairs, I have just a thermostat. Upstairs, I want to have both a thermostat and a TRV. The problem is that the thermostat is in a room that is always warmer, and I have no idea why. So, I installed a TRV in the second bedroom. However, now whenever the bedroom calls for…
-
Smart Thermostat (v3) not firing boiler (was working previously)
Hi everyone, I wonder if anyone can help. Firstly, I should say I am a long time user of Tado with everthing working correctly until today (I chose to resume all schedules last night where previously it was set to OFF) - so have only noticed this today I should say. I've had a very odd experience in that the heating is not…
-
Official Announcement: Sunsetting IFTTT
Hello Community, Many of you have already seen other threads regarding this topic. However, if any of you missed the threads or did not receive the email announcement, you can find tado°'s official statement regarding the end of its integration with IFTTT below. _____________________ At tado°, we are continually striving…
-
Faulty SRV?
I have two wireless smart thermostats and four Tado SRV's in our property and they've all worked just fine from the start, aside for a teething issues with the receiver, five of the smart thermostats operate as they should and turn the heating on and off, either manually or to a schedule. Yet one will only turn on the…
-
Vaillant Boiler Overheating (f.20)
Hi all, I have a wireless thermostat and 6 smart thermostats on each radiator. I don't have any other radiators in my flat meaning they all have a dedicated radiator thermostat. I also have a Vaillant boiler (ecotec plus). When I bump up the heating in all rooms (all 6 radiators) the heating usually works fine. Still, when…
-
New installation. Upstairs radiators always on, downstairs always off.
I just installed the wireless V3+ starter kit and despite having a schedule of the heating turning off and on at different times, the upstairs radiators are always on and the downstairs radiators are always off. I also tried setting the heating to off in the app, no change. I replaced a danfoss tp9000 and tp4000 with the…
-
Hot Water turning on but heating isn't
Hi all Complete novice here and British Gas had no idea how to fix it either. I have a V3+ kit with two separate zones for my underfloor heating and then the rest of the house is controlled by TRVs. The underfloor heating is connected to a wired thermostat. Initially, everything was working fine for a few months. For the…
-
EMS bus support UK
After purchasing a V3+ wireless thermostat kit 10 days ago and being disapointed in it not having EMS bus support I now come accross this you tube video stating that it is now going to be re-instated Is there likely to be any chance of tado upgrading recent purchases, and if not where can you purchase the newer controllers…
-
Boiler not firing after power cut
Earlier the afternoon we had a power outage to our house. The power returned after 5 mins. At 4:15 I noticed the boiler hadn’t fired and the heating was not on. It usually comes on at 4. I looked on the app and the wireless receiver was showing as disconnected. I reset the receiver and turned the bridge on and off again.…
-
Boiler pressure dropped after installing tado
After installing a tado WiFi reciever Internet bridge and thermostat on my Alpha InTec 28XE combi boiler central heating and hot water were lost after 2 days due to a drop in water pressure. This has never happened since I moved in 2 and a half years ago, so it would seem an unlikely coincidence. I was getting error code…
-
How do I keep the 'INDEPENDENT' setting on some new SRT's
Hi, I have just added 7 new SRT's to my system, but none of them will retain the 'Independent' setting when selected. When I go back to the Rooms & Devices menu after choosing Independent (Image 1), the SRT reverts back to Zone Controller (Image 2). The existing SRT's are all fine and were set up and still operate…
-
Tado v3+ wired connection to Intergas HR boiler
Hello all, I have replaced an IT Salus 500 thermostat with a Tado v3+ wired. The boiler wires on the old thermo were connected to the COM and NO terminals. I tried the same on the Tado but it doesnt control the boiler, it seems to be on all the time regardless of the temperature setting. Can someone help please ? Kind…
-
Have I got my set up wrong?
Hi All, I've been thinking about my set up and think maybe I've got it slightly wrong, would love some advice from you experts! I have an upstairs and downstairs zone, both of which have a wired thermostat from Tado installed. I have a combi boiler and a hot water tank / cylinder / immersion heater (TBH I'm not sure!) in…
-
Tado radiator thermostat doesn’t calibrate
I have one tado radiator thermostat that won’t calibrate. It used to work and been fully functional for over a year. It also only briefly flashes ‘Hi’ for a fraction of a second, when prompted by the app. The brightness of the display is also very low. The batteries have been changed. Any help would be appreciated.
-
HERMANN SPAZIOZERO 4 CONDENSIG EBUS
I have had a new Hermann Spaziozero 4 condensing boiler installed. It uses Vaillant's eBus bus. So I reset my Tado V3+ using the ebus with code D07. The boiler makes hot water correctly and turns on the heaters. wanting to check the Tado settings on the Max Flow Temperature in modulation, either from your site or from the…
-
Adding internet bridge stopped the heating and boiler working
Hello, I've searched through the forums until I'm reading everything 5 times and can't find the answer. I am renting a house and there was already a tado set up, from what I could find there is a smart thermostat and trv on rads in most rooms. There are regular rad controllers in two rooms, one beside the boiler and the…
-
Tado thermostat not powering on after battery change
Recently changed my batteries on my Tado stat and noticed it wouldn’t power on. Checked battery voltage and orientation in the compartment and both were good. Decided I would have a look inside and verify power circuit, the case is very easy to pop open using a small flathead screwdriver and just gently push the side out…
-
Need online support from a Tado expert for my installation
I have moved into a house from 2001 with underfloor heating and old thermostats. They were controlling the actuators of each zone of the underfloor heating. These thermostats have been replaced by tado wired v3+ But they do not seem to work/ no movement of the actuators. I am looking for a tado savvy / expert I can pay for…
-
Checking compatibility - Worcester Greenstar boiler, Salus thermostat
Hi! Am interested in buying a tado with my Bulb discount. But I wanted to check compatibility before I buy, just to make sure it works with what we currently have. We have a Greenstar 32CDi boiler and a Salus ST621RF thermostat. This is a wireless unit with a receiver on the boiler. Had a fiddle and seems to be tricky to…
-
Energy IQ ft3/Imperial
Hi I know you can't enter ft3 meter readings at the moment. Is there anyway to use Energy IQ if you have an imperial meter like this? It would be useful to me as I can't get a gas smart meter installed due to the location of the meter. I know this has been mentioned before but I'm just wondering what other people in the…
-
Tado not talking with Alpha E-TEC boiler? It's freezing :(
I have an Alpha E-TEC 28 boiler, which previously had an Alpha Easy Stat wireless thermostat connected. I removed the old thermostat and receiver, have installed the new Tado Wireless V3 starter kit which shows as all connected on the Tado app but the boiler won't respond to the Tado, in-fact my heating won't come on at…
-
"Your system is not supported" [Climote]
I'm trying to install the Tado Wireless Receiver to be the controller of my boiler (regular / open vent, Ideal SE18 18kw gas boiler). Until ~2 years ago, I had a very standard digital controller to set which hours the boiler would come on, and be able to boost. About 2 years ago, I had the Climote installed by my utility…
-
Energy iq
Can you help I use lpg and price is £0.48 ltr. However in the app it K watts. How do you convert ltr to Kw thanks
-
New EcoTec Plus and Tado V3 Wireless. NO HEATING :(
Hello, I’ve just had a few boiler installed and the Tado V3 system to accompany along with 4 TRVs. If I set any TRV in the house to call for heat the boiler does not respond. I’ve tried the boost button and adjusting both Tado and traditional TRVs manually. If I hit the heating icon on the Wireless receiver then the boiler…
-
Replacement for IFTTT's WiFi connect/disconnect based routines
I moved from legacy tado system to X where there was no IFTTT support anyway, however I used a very helpful logic where connecting to a specific WiFi network would turn off the heating and disconnecting would return to automatic. Is there a replacement for that? Neither Alexa nor SmartThings allow such trigger.