-
No Heat! How do I fix it?
Hi All, I had someone install my tado v3 kit a few days ago. I have since found I have hot water but no heating. The App says it's on, and the light on the wireless reciever is on, but the pump in not pumping and the boiler is not firing. I have attached a picture of the current wiring. Can anybody tell me if this has been…
-
Starter kits
Just to confirm this is still correct with wireless starter kits at this time. uk version with weather comp euro version with open therm Thanks
-
Temperature change
Hi, I have my Tado set to a schedule but i have noticed the temperature goes up from the set temperature in a couple of rooms and I need to press the schedule button to re set !
-
Hot water just turns itself off when using Alexa
I use Alexa voice control to turn the hot water on, but I'm finding sometimes it will stay on for an hour or longer, other times it will randomly turn itself back off after only 10 mins. I don't have any schedules or time blocks set and I've tried it on both home and away modes and still have the problem. Hoping someone…
-
Underfloor and radiators system
Hi, I am looking for some help on which Tado products I need for my heating system... I have a gravity fed Y plan system with 1 zone underfloor heating downstairs in our kitchen/diner and the rest of the house on radiators. I would like to control the underfloor separately to the rest of the house, how do I go about this?…
-
Best setup for central heating from building
Hi, I’m new to this topic and would appreciate help in selecting best setup. Many thanks in advance!! Setup - I live in a building with communal heating (central boiler runs 10-22hrs, I cannot control it) - heating reaches my apartment through a main valve at the entrance, which is controlled by a radio “dumb” thermostat -…
-
Heating not going off
I have just fit the tado V3+ starter kit to my glow worm ultimate 3 30c combi I have got everything paired up as per instructions but the heating will not turn off even though the heating indicter on the receiver is off. I have noticed the Htg symbol on my boiler display flashing which it does when a Htg demand is req.…
-
How to add wireless temp sensor to hot water control
I had a working system for a few years then my wireless temperature sensor seemed to die. So I replaced it with a new one. I can't figure out how to add it to the hot water control. It now only shows the main box where it also displayed my previous wireless temp sensor which I've now removed from my setup. Hot water had…
-
Two boilers, two protocols, two thermostats?
So... I'm looking into replacing my current Nest thermostat with Tado. Our situation is as follows: Old part of the house: 8 radiators, wired thermostat on boiler one (opentherm). New part of the house: Floor heating, no thermostat yet on boiler two (EMS). Now I was thinking of getting the following, but I'm not sure this…
-
Changed boiler now Tado won’t communicate
I recently changed my boiler and moved to a new position. Tado receiver has not moved. Trying to re wire the new boiler back in and tado receiver is not turning heating on or off. The receiver clicks and lights up when I use the app but the boiler does not respond Could someone one help confirm that I have the wiring…
-
Issues with Tado keeping valves closed this season?
Hello, I have been using tado sind september 2022. The overall use of the system in that season was satisfying. However, since I started the system last Sunday, I have noticed weird behaviour of the system. First indicator was looking at the „Energy IQ“ module of the app. There I could see the predicted costs have reached…
-
Replace Danfoss RX2C and Danfoss FP715Si
I have a Danfoss RX2C with a wireless room thermostat and a hot water thermostat. These are all linked to a Danfoss FP715Si controller. I recently purchased a Tado V3+ starter kit and in the instructions for the Wireless Receiver I can select either the FP715Si controller or the RX2C, but as far as I know these 2 do not…
-
What to do with zone controller 'dummy room'?
I have three zone valves in my house: 1) hot water tank; 2) downstairs heating; 3) upstairs heating. Following guidance from these forum pages, zones 1 and 2 wired so as to be activated by the extension kit, and zone 3 is activated only by a wired smart thermostat. So far this works ok; rooms (using a mixture of smart TRVs…
-
Is the V3+ voltage free or low voltage?
Is the V3 plus voltage free or low-voltage? I have a voltage free boiler which is constantly on and cannot get infinity answer
-
Tado thermostat
Hello, I’m using tado for about 2 months and noticed weird behavior. Is that normal when temp drop by 0.1 boiler is triggered? It doesn’t make sense for me as my bill is 13€ per day! I’m using single wired thermostat. I noticed is better to set lower temp but heat 2x or 3x for 1h or less every 2h or whatever to higher temp…
-
How to connect the wireless receiver to my system
Hi guys, I have a tado wired thermostat which is in my living room that controls the floor heating. I have radiator thermostats in the first floor and the attic. Recently I found out that tado only heats up the radiator when the thermostat in the living room requests for heating. I have city heating and I live in…
-
boiler not firing
hello - problem with my tado system wired extension kit boiler doesnt fire when the radiator smart thermostats call for heat boiler fires when hot water is turned on help!
-
Should my boiler Alway be heating
I have an atag is18 boiler, 10 radiator valves, Controller and a wireless thermostat. Only had it all for a week and slowly working it all out. But even if I select all rooms to off the protect/care tab says that my boiler is heating? Is this correct? Many thanks
-
Fitting Tado remote to Ideal Boiler Vogue 32 Gen 2
Hi I have Tado valves fitted to radiators heated by the above boiler but working independently. I would like step by step guide to fitting the Tado remote thermostat to replace the ideal remote thermostat. Any help appreciated Thanks Graham
-
Danfoss adapters
I am new to this and apologies if I have missed the answer elsewhere on the forum. Can someone please advise how to fit the smart rad head to the pictured valve below. Thank you.
-
Adapter for EPH 75 TRV
Hi. New to Tado, but have successfully set up SRVs on four of six radiators. All six radiators have EPH TRVs but two of them don’t fit right- the SRT from Tado only screws on part of the way and then stops before the plastic tightens up so it remains loose. The valves are marked 15 & 94 on the ones that fit, but the other…
-
New wireless temoerature sensor and reciever
Hi any help greatly appreciated . I removed a nest wireless thermostat on a simple system boiler. When installing the tado I couldn't find my boiler and pressed a Honeywell controller . The thermostat now control the hot water output. How do I configure the reciever to simply control the boiler output to turn the boiler on…
-
Gravity fed system with no thermostat - Sanity check wiring plan
Hi All, I just wanted to post here and sanity check my proposed wiring before installing. We currently have a gravity fed system with no thermostat installed. Controlling both hot water and heating is done via a simple timeclock wired into the switched live on the boiler. When the timeclock is switched on both hot water is…
-
Tado wiring for switching a floor pump
Hi, I have one floorpump in our livingroom which I want to turn on and off when Tado wants to heat the livingroom. The current setup I’m using is an automatisation within Home Assistant that switches on/off a smart switch which turns on/off our floorpump. But what I don’t like is the dependency on Homeassistant. Is it…
-
Tado and Google Home
hi. is there any guidance for what I should I say for Google Home to instruct Tado? I have connectivity but verbal instructions always default to one room. All other instructions ( alternative rooms etc) respond with ‘ it looks that thermostat is not set up yet’! although occasionally it will work randomly when instructed.…
-
Does anyone know what versions of EBUS are currently supported by Tado in their wired or
Hi, I'm looking for a straight answer on what versions of EBUS are currently supported by Tado in their wired or wireless extension kit? I did see a post from 2019 saying EBUS was supported up to version V65 is that still the same or are more recent versions now supported?…
-
Heat pump connector availability in the UK
Is there any plan to release the heat pump connector into the UK market?
-
Is it possible to increase the minimum opening size on the radiator valves?
Hi Sometimes my radiators are wheezing (not just with the Tado smart valves, but the old manual ones too), I think when most of them are closed and a few ones are barely open. Now this is not an issue with the manual valves, I just set them to an opening when they are not wheezing. Because Tado adjusts them automatically…
-
Vokera vibe wiring
Hi I was fitting a tado to my brothers with the above combi, and when setting the tado up it couldn’t find the boiler model, do we email support for wiring instructions ? Thanks
-
what is the correct way to connect my Tado wireless receiver to my Vokera Compact 29A combi boiler
a wiring diagram for my question would be very.helpfull. Cheers