-
Wunda floor heating replace Hortsmann Channel Plus H37XL, 3-zone timer with Tado
I want to replace a Hortsmann Channel Plus H37XL, 3-zone timer. My radiators and underfloor heating and water are controlled with it. The underfloor heating control box is a Wunda floor E8.583RF Wireless Control Centre, a photo of the circuit connections is in this PDF here -->…
-
Can Tado work alongside an underfloor heating system?
Hi, I'm considering buying a Tado Home Bundle - Wireless Starter Kit + 4 smart TRVs (great offer at Costco at the moment). I currently have a two zone heating arrangement in my house, namely an under-floor system on the ground floor, and conventional radiators on the upper floor, all operated by a Horstmann H37XL Three…
-
One room overheating
One of my 7 room stats is still heating to 24 - despite me switching it "Off" on the App. The underfloor heating actuator for that room is showing that it is drawing heat from the boiler (top popped up). All the other rooms are behaving normally (set at 20 degrees - as set in the Smart Schedule. ) I have tried re-pairing…
-
One device makes room go offine?
So I have a room in our commercial building with 7 radiator thermostats and one wireless controller for that space. Once in a while one of the radiators will lose connectivity diabling access to the remaining devices via the app. The app tells me the room is offline because one device is offline. Is this normal? Is there a…
-
V1 radiator thermostat issue and replacement
Hi all. I have a V1 setup with 24 radiator valves. One seems to be bricked. It won't ever boot fully and start the calibration process. First question... does anyone know how to overcome this? I've tried disconnecting for several days. I've ensured it is close to the bridge, I've tried reset. Firmware is 54.20. Second…
-
Smart AC Control in synch with IR remote?
If I use the IR remote control to change my air conditioner settings (e.g. on/off or change temperature setting), will the Smart AC Control be updated to the new status? And will the tado app therefore also show the new status?
-
Stuck with Salus IT500 replacement and another thermostat
Just bought the wireless starter to replace my Salus IT500. Can anybody help me with installation please. I use it via the app or black coloured wireless Salus control. Picture are attached. Other thing I have seen is an wired thermostat in the kitchen (that could be a seperate underfloor heating thermostat but not sure)…
-
Android constantly using location - how to stop?
I've upgraded to Android 13. I now have a permanent green dot showing that Tado is constantly using my location. When I click on the notification it says Tado last accessed the location an hour ago and is allowed all the time. Is there a way to stop this while keeping geofencing? None of my other location based apps cause…
-
New flat
Hello guys, i am building a new flat. The flat will have underfloor heating zones (Master bedroom, Bedroom 1, Bedroom 2, Master bathroom, Main Bathroom, kitchen, hall and living room) So thats 8 zones for heating. Now for Air Conditioning, i will have a VRV from Daikin, 4 different airconditions. My questions are: How will…
-
Test in the App !
The name of the ROM is in half ? Have been trying to delete the App and indstalleret again without any success. Best regards Bo Cramer
-
Lost hot water tile
For no apparent reason both users have lost the hot water tile on Home Screen. Any idea how to get it back?
-
Vaillant VRT30 wired thermostat
Hi all I am replacing a VRT30 with a Tado wired thermostat. The VRT30 is connected to a controller that will be set to constant for heating. The VRT has the following cables that I am trying to understand so I can connect to the Tado. 3/L 4/☀️ 5/N Can anyone advise? Many thanks in advance. Rob
-
Adding non Tado smart valves to system
Hi just wondered if anyone had added non Tado valves to their system, thinking of adding some others and controlling them through HomeKit/home assistant, reason is the cost of Tado and smart features, and later on jumping completely to another system ?
-
Upgraded from V1 to new V3+ Equipment
The upgrade process went relatively smooth, however I appear to be unable to move the hot water over from the old 'smart thermostat' to the new 'wireless receiver with water'? Hot Water control is still pointing to the old device in the app & I've no way of checking that we are actually getting hot water at this stage.…
-
Does Tado with ebus have a 'learning' phase?
Hello, I was wondering, if using the wired Tado V3 and ebus via the +- connections, will mean that the first few weeks of a new installation be a 'learning' phase for Tado? Meaning, will Tado be logging inside and outside temperatures and timing how long it takes to heat my house in different scenarios, adjusting itself…
-
I have two brown wires in Terminal 5
I am going through the step by step and have come to the connection phase. In Terminal 5 I have the bridge wire and two brown wires. The bridge wire is no longer needed, the two brown wires have stumped me? It’s says to treat them as the cable in terminal L. Does this mean they all go into L totaling 4 cables ?
-
Smart AC Control does not maintain the desired temperature.
hi, my Smart AC Control usually continues up to 3 degrees above the set temperature that I have set and that is shown in the display. Can I set a working temperature it works in between.
-
Geofencing on Android 13
Hi all, since I updated to Android 13 Geofencing cannot be enabled because it requires to set location permissions to "Allow ALL the Time" and this setting is not available anymore. Now I can only see "Allow only when using the App". Has anyone come across this and has resolved it? I am using Tado app on a Xiaomi Remi Note…
-
Megatherm Wired?
Hello How should I put the cables in the tado? My Megatherm thermostats do not appear in the guide. I can't upload a picture?
-
OPEN THERM - 2 Zone Heating
Hello, Is it possible to use a TADO control (or 2) and connect them both via an OPEN THERM Connection on a Combination boiler? Thanks Tony
-
Wired or wireless
I can't work out if my current system needs wireless or wired products. This must be a common issue. I have a new vaillant system boiler, a honeywell wired control/timer box, and one one honeywell wired thermostat. Radiators have drayton TRV's. I have just built a new large kitchen extension, and we spend most time there.…
-
Help, no “switched live” on boiler
I don’t appear to have a switched live on my boiler which is quite old Worcester HPJB.19000. Wire to boiler goes to thermostat in boiler, which appears to be removable, then onwards to boiler. How can I overcome this to make the system work with Tado? The wiring diagram specifies switched live so not sure what to do next?
-
Tado app NOK on iPhone XR but works on other devices ... ?
hi everybody, anyone able to help with this strange phenomenon : I have Tado app running on a (very) old iPhone (model 9?), on my iPad and also in Safari browser on Mac + also on my daily usage iPhone XR. all four connections worked perfectly since months, not an issue at all (and very happy with Tado !!) but since a few…
-
Tado with floor heating plus radiators
Currently I have the following setup: * Downstairs: Wired Smart Thermostat with 4 radiators. Radiators have taps (not thermostatic valves) * Other rooms: Tado TRV knob in each room radiator. I'm planning to upgrade the heating system as follows: * Downstairs: Wired Smart Thermostat with 3 radiators. Each radiator will get…
-
Wiring New Tado Receiver - Changing from BG Hive single channel.
Hi, I'm changing from a Hive single channel to a Tado wireless smart thermostat starter kit V3+. I've used the app, labelled everything and wired it up but there are no details about the earth wire. If I put the earth wires in the terminal with the downward arrow (between HWNO and P1), the fuse board blows when turning on…
-
Is Tado Smart AC controller compatible with De’Longhi Pinguino PAC EL112 CST?
Hello Tado Community I am considering buying the Tado Smart AC controller for my De’Longhi Pinguino PAC EL112 CST portable AC. However, I would like to know if Tado Smart AC is compatible with the Bluetooth Low Energy remote of the Pinguino AC. Thank you for your answers! Florian
-
Energy IQ chart
the chart showing the cumulative energy usage has stopped working it is just showing the daily usage i.e a flat line now whilst there’s no heating . How do I get the chart to show the cumulative usage on a daily basis ?
-
Wireless receiver EU version for Worcester HighFlow 440 CDi
Hi everyone, I'm looking to change our wireless receiver UK version to the EU version as I believe the EU version support Worcester EMS which means that we'd be able to have load compensation, have I understood that right? If someone have done this, has it been working well? Anything I should consider before starting? My…
-
Tado won’t stop the central heating after internet hub changed
Hi, my tado starter kit has worked without any issues in the last year until few days ago when I have changed the broadband package from virgin with the hub 5 and 1gig speed. After I reconnect the bridge to the new hub my central heating is always on. Only way to stop it is to remove the smart thermostat from the wall…
-
V3+ AC have to send ‘off’ to wake the tado
Bit of an odd one, if I want to turn on my AC I have to send an off command first otherwise the unit doesn’t beep and respond. Is this normal or is there a setting I’ve missed.