-
New Viessmann Install + Weather Compensation, Tado Confusion
Hi All, Forgive me for asking potentially a stupid question.... I just had my old combi boiler (with Tado) swapped out for a new Viessmann 100-W 35kw with the weather compensation fitted. The boiler installer disconnected the Tado from the boiler, and only left power going to the Tado extension kit (so that we can actually…
-
New CH and HW install - issue with CH control
Hello, I've installed a Tado V3+ Heating & Hot Water Wireless Smart Thermostat Starter Kit for my partner and struggling to get it to work. It's on a Y/S Plan setup. The old programmer was a Drayton Tempus 6, with a Honeywell RTS1 Thermostat. There's an Ideal FF-350 classic boiler providing CH and Hot Water to a Megoflo…
-
Install Sanity Check - Alpha InTec2 (ST9400C -> Tado Wireless Starter Kit)
I have a faulty ST9400C that needs to be replaced and am looking to upgrade to Tado Current setup is as follows: Alpha InTec2 boiler ST9400C Alpha Wireless Receiver The ST9400C config is as follows: The wiring is as follows: 1 - Earth (move to position 9 on wireless receiver [earth]) 2 - Neutral (move to position 1 on…
-
Wireless thermostat to act as dumb temperature gauge
Hi all, I am looking for a solution to monitor the temperature in the garage where my boiler and hot water tank are located. I’d like to know when there’s a risk of freezing pipework and maybe also use the temperature to run an automation and alert me to the risk. I’d like to do this through HomeKit so today I purchased an…
-
Calendar
Please enable to set future settings, eg. for planned holidays.
-
Smart TRV question on new setup
Hi, Thinking of chanign my CH setup to a Tado. Setup: Ideal combi boiler - dual zone CH valves for seperate upstairs and downstairs. Downstairs controlled by a wired ESI thermostat in the hallway - rad in the hallway has no TRV on it, rest of ground floor rads do Upstairs controlled by a wired ESI thermostat in master…
-
Show heater status
Show a right led when the heater is actually heating to raise the room temperature. Show a white led when the heater, the thermostat or their connection are out of order. Show no led when room temperature is as demanded.
-
Tado Smart radiator, thermostat not working properly (flat temp and inconsistent)
Hi all, I have a count of 5 Tado smart radiator thermostats. I bought all new, but one of them, after three months of use, started to provide an inconsistent room temperature and remains flat even for humidity. During the summer, I kept the device with no batteries inside, and after six months of no energy, no positive…
-
Replacing Honeywell smartfit to Wired Tado thermostat
Hello, I'm not one for electronics, but my wife and I have just purchased a new wired thermostat to replace our Honeywell T8677 Smartfit. I've followed all instructions, but can't figure it out. Any help would be appreciated!
-
Does anyone know what this means??
I occasionally get both these LED's blinking at about 1 second intervals, does anyone know why?? We don't appear to have any issues with control or anything else and i can't seem to find this listed in any manual?? Many thanks, Andy
-
2 Heating zones in one house
We have a 2 heating zones in one house with thermostaat model Vitotrol 300 en Vitotrol 200. I have now 2 smart Tado termostats en I wil to instal but I have a problem. Vitotrol 200 work on Heating circuit 1 en Vitotrol 300 on heating circuit 2. With Heating circuit 1 I dont have a problem but whnen I folow the instalation…
-
Bridging wired thermostat v/s wireless receiver
Hi all, I have a v3 kit with a wired smart thermostat and wireless receiver. I also have smart radiator thermostats installed. Since the installation only the wired thermostat can call for heat. The Trvs cannot, they just shut off when they reach the desired temperature (providing the wired thermostat is calling for heat).…
-
central heating is turned on when hot water is turned on
central heating is turned on when hot water is turned on. why? I am expecting the CH will remain off and the HW is on
-
Adding smart TRVs had stopped my wireless thermostat functioning as expected
I’ve recently upgraded my V3+ wireless thermostat system (which had been working fine) by adding four smart TRVs in different rooms to the wireless thermostat. Ever since doing so the ‘system’ no longer seems to be promoted by the wireless thermostat to turn on the boiler, that room will get cold, the app says that room is…
-
Read/Write Operation Failed
I have multiple devices and a bridge, all working okay in the Tado app, but they are no longer visible in the iOS home app. On the Tado app, they are all eligible for firmware upgrade, but when I try to upgrade any of the TRV’s or thermostats or the Internet bridge, I get a 'read/right/operation failed' error The Internet…
-
Is it possible to get information from the Tado about the Hot Water supply being active ?
It is possible to set the temperature and a schedule on when the system should provide hot water, but i am missing the information on when actually the system is getting a Hot Water request. (So DHW, not CH !) I used to have a HomeWizard system that showed me when Hot Water was requested. I would need this information to…
-
Changing from heatmiser to tado
I would be grateful for some advice. I have half upgraded to tado, fitting smart thermoses to all my my radiators (7). I would like to add tado thermostat/s.. We have a Worcester Greenstar 42 CDi Classic combiboiler and 3 Heatmiser thermostats. At present only one thermostat will turn the boiler on and if not on the…
-
Multiple radiators in one room
Hi, Some of my rooms have two radiators. They already have dumb TRVs on them and I'm intending to get a limited number of smart TRVs for my house - with the intention of adding more as time goes on. What do you recommend as being the best approach for fitting smart TRVs where there are more than one radiator in a room? Do…
-
How to bridge a Drayton Combi Stat to enable Tado Wireless receiver to work correctly
Hi. Today I had the EU Wireless Receiver delivered to complete my system, however I believe I need to "bridge" the legacy wall mounted Drayton Combi Stat. Does anyone know how to do this? My system is as follows.... ---------------- Vaillant ecoTEC plus 837 combi boiler. No hot water tank. Tado Basic rad thermostat and…
-
Apple HomePods - new software update will enable temperature & humidity sensors
Apparently existing HomePods already have temperature and humidity sensors built in and these will be enabled with Software Update 16.3. I wonder how much this will be able to integrate with the Tado infrastructure. Probably only through HomeKit as I'm sure Tado doesn't want people to be able to buy a HomePod (with all the…
-
Why doesn't the boiler do what I set in Tado?
Hello. I can't control the boiler using Tado. The system was installed by previous owner, but I can't get them to work together. No matter what changes I make in Tado or whatever temperature is shows, my central heating wouldn't stop working and doesn't settle on the temperature I set in Tado. Everything seems to be…
-
New Boiler. Trouble installing my Tado!
Hi all. I’ve recently had a replacement boiler. Greenstar 4000 - GR4700W C. The boiler was upgraded (unknowingly) and therefore came with a wireless thermostat. I own already a Tado wired thermostat which worked fine with the old boiler. I’ve downloaded the manual for the boiler, but either cant make sense of how to wire…
-
Thermostats to control TRV
I’ve got a 4 way underfloor heating manifold (under the stairs), that I want the smart radiator heads to control each output on the manifold, is there a way of adding a smart thermostat in each room that will control the smart TRV on the underfloor heating manifold. Thanks
-
RF interference . . .
Last Friday we lost our broadband feed. It’s not yet clear whether the router or the line is at fault though I suspect the latter; OpenReach is sending an engineer to sort things out this morning. During the outage we’ve been operating the TRVs and wireless temperature sensors manually which is a pain but has kept the…
-
Rename air conditioning units
I have since recently air conditioning units in different rooms at home. I bought the airconditioning system from Tado thinking it would have similar features as the heating knows when using the app. But it doesn't. It's impossible (to my knowledge) to rename the separate units in the app, meaning that I'm too often…
-
2 zone system, no hot water, combi boiler
First things first, i am amazed by the minimal amount of documentation that exists for the controllers! Now, to my issue (which i have seen a lot of people posting but nobody wrote a clear solution). I have a combi boiler so water is getting triggered automatically. I have 2 zones that get triggered as simple relays. I…
-
Multi zone in a 3 storey town house
Hi all, I have set up the Wireless Smart Thermostat V3+ (replaced Danfoss TP9000), a Add-on Wired Smart Thermostat (replaced Danfoss TP5000) and a few Add-on Smart Radiator Thermostat installed on the radiators. My home is a 3-storey townhouse with 2 heating zones. The TP9000 controls the water heating and the ground floor…
-
Modulation control in system boiler
Hi all, I am new to the Tado community, and just purchased a V3+ wireless smart thermostat starter kit as I have a dual hive setup (HW and CH) and am interested in having more control of the system, and hopefully lower energy bills as a result. I have a Worcester bosch greenstar 4000 18kw system boiler with unvented…
-
Tado password with new modem
Having a new modem and it is so long since I set Tado up (trouble free!) that I've forgotten what I might need to do. Presumably change to the new password. Will it just ask for it or will I have to do it in settings somewhere in my account?
-
Don’t understand how it works
Hi. I got a Frisquet hot water heater with its own thermostats. Get 7 heaters at home and I recently bought 7 wifi tado thermostats with a smart thermostat. I don’t want to replace my frisquet thermostat. I just want to use the 7 wifi thermostats linked to my wifi via the smart thermostat. So how to set up such an…