-
Provide method to specify type of heating system, i.e. radiators, underfloor, etc.
There is no facility to specify what type of heating system is installed. It appears Tado treats all systems as if the heating system is based on radiators. In case of a underfloor only system it is likely the floor is cold when the first call for heat after a break is generated. Currently the system would start to run for…
-
3rd party temperature sensor support or cheaper add-on temperature sensor
I have multiple tado radiator thermostats, but all of them are a couple of degrees out with the actual temperature. I use an Aqara temperature sensor to measure the actual temperature in the room, further away from my radiator. It would be great if the tado app could use the data of these aqara sensors to measure the…
-
Notificación al móvil en caso de encendido/apagado de calefacción
Una sencilla forma de saber si se ha puesto en marcha la calefacción en nuestra casa (o en una estancia de ella) a través de una notificación al móvil (tira o globo) especialmente si nos encontramos fuera de nuestro hogar. Igualmente se podría notificar apagado de calefacción. Estas notificaciones podrían activarse o…
-
Set Humidex instead temperature
It can be useful to have the option to set the perceived temperature instead only the normal temperature. In the high humidity zones temperature is not significant. It would be nice to trigger the air conditioning with your wireless control to decrease humidity.
-
Smart wall plug for underfloor heating pump
You offer nearly everything except a way to turn a underfloor heating pump on or off. My living room thermostat is connected to the underfloor heating, and to control the pump I have to set up a complicated process through Homey and a Z-Wave smart wall plug. It would be great to have a Tado smart wall plug which can be…
-
Tado app return to 0.1° granularity for setting manual temp
Very frustrated to find I have lost the ability to set a temp of 20.8° in the app. 20.5° too cool, 21° too warm - but those are the only options now. Why has this been changed?! It worked fine before!
-
Switch between rooms in graph nice
When in graph mode, one can change the date range with the ˅ symbol next to the date. It would be so much easier to switch between rooms if there was a ˅ next to the Room/Device name as well. Now I have to go back twice (first to the Room, then to the home screen) to select a new room and view the graph
-
[Released] Show the climate report in browser on tado.com
In the app on my iPhone I can see the heating history which is great, but I don't understand why I can't see this when I access my tado account on tado.com using a browser running on my desktop computer.
-
temperature adjusted at the radiator valves
If the temperature is adjusted at the radiator valves, that new temperature remains set until someone adjusts it again or until someone chooses to go to the schedule at the next schedule change. I would like to be able to decide myself via the setting what the reaction should be when turning the radiator valves. In my…
-
Humidity visualization and routine with modality home, away
It would be useful to have an indication of the humidity directly on the room box to have an immediate idea of the environmental well-being. Also on the environmental well-being box to have a summary of the situation without clicking on it. It would be useful to have the possibility of programming the "home" or "away"…
-
Different Scenarios for Heating Schedules
Loving the Tado (but hating the 10 room limit) and I would like to make a heating scenario suggestion. This is to allow simple, perhaps temporary, changes to the heating schedule according to a set programme based on scenarios. The current way of working is to set up one scenario of daily heating and any changes require…
-
[Released with tado° X] Integration for Samsung SmartThings
It would be great if we Tado users could connect Tado to Samsung SmartThings
-
[Released with tado° X] Make the Smart Radiator Valves quieter
I find the Tado Smart Radiator Valves are too noisy for use in bedrooms. The motor noise when opening/closing the valve is loud enough to disturb sleep. I have had to set my bedroom schedule in a way that ensures the bedroom heating will never turn on when we could be asleep, and so have to manually turn it on everytime I…
-
Be able to see when heating was on in all rooms on one chart.
I like that I can see what times of the day the heating came on in a given room, but it would be great if I could see all the times the heating came on, in all rooms, at the same time in the same chart. This would help me to see my usage much better than checking 7 devices separately and reduce energy usage. E.g. I may…
-
Use Smart AC Control also as a temperature sensor for smart radiator thermostats
I have a room with both AC (controlled by a TADO Smart AC control) and a radiator (with a TADO smart radiator thermostat). The room is big and the temperature around the radiator in the winter is not what most of us using the room feel. The TADO Smart AC control is instead in a place where temperature can be sampled more…
-
Individual Geofence Option
Hi. Not sure if this has been mentioned before, but would be great if you could set-up individual Geofencing capability for each individual Smart Radiator Thermostat. To explain, I am often away from home for several days at a time for work and would like to be able to automatically detect this and shut off the Radiator…
-
Widget
would be really great if developers can adds widget for both android and iOS.
-
Tado X wired with OT changes the temperature of domestic water
In my boiler, Tado X wired thermostat connected through OpenTherm changes domestic water temperature to 60 degrees even if it is not supposed to. When this happens the temperature cannot be adjusted anymore from the boiler: if one tries to change it from the boiler settings, it immediately goes back to 60, as if Tado X was…
-
Set minimum opening percentage on smart radiator valves
Despite fiddling with pump speeds and lockshields, I still get water rushing noise in some of my radiators when the smart valves are open only a small amount. Being able to increase the minimum opening percentage would prevent this.
-
Home planning quiz
I have just installed a heat pump and I know I will need a heatpump optimizer, but I don't know if I need a Programmer with Hot Water Control also. It would be useful to have a way to get the best possible solution for one's home based on a quick quiz to design the right system for one's home
-
Open Window Detection Accuracy
Hello, I have recently bought tado x and was disappointed by the open window detection. There should be a manual button to say that the window is opened it shouldn't rely only on fixed changes of Humidity and Temperature ( Some spaces takes more time to lower the humidity and doesn't detect the window is opened) when…
-
Limitations for larger properties
So, I've got a large property - 19 rooms 10 downstairs including hall, 9 upstairs including landing. Its an odd L shape as well which means i have concerns about distance. I was excited when i read tado supports 25 devices... and then i realised the limitations...having spoken with 1st line support... I want to zone each…
-
TADO notifications when the boiler isn't working.
It would be really cool to have an active notification feature for users where tado demands heat and for whatever reason, the house does not get warmer. Notifications should include emails as well as tado badges. use: Unattended Property - know that the frost protection has stopped working - (for whatever reason) I have no…
-
Hot Water 'Boost' Button - 30, 60, 90min options
We have been using TADO for 2 years - and its worked well, and so recently installed the Hot Water head unit. We find that there is a big need to have a quick way to turn on the Hot Water for just enough time to heat the tank for one bath/shower or to heat the tank for a couple of bath/showers and then possibly even…
-
Enhancement to Energy EQ - add specified radiator output to rooms
To assist Energy EQ in estimating the amount of energy/cost per room, allow the addition of the total radiator BTU output per room. Even without knowing system flow temperature, as long as the total radiator BTU specs per room were added (all need to be at the same rated temp as not all use 70 degrees), combined with the…
-
Consumption graphs: add option to scale the graph from 0
It would be great if there was an option to make the vertical axis of the consumption graphs scale from zero, instead of showing them as a "zoomed in" scale e.g. between 14°C and 22°C or whatever. It's clearer to see patterns and the peaks/troughs are less exaggerated from 0. It's also impossible to compare graphs over…
-
Smart AC Control X
You should definitely make a Smart AC Control X. Tado X is awesome, but the finishing touch would be automatic dehumidification. Using the air conditioner to dehumidify in the winter is a lot more energy efficient than opening a window. I'd love to be able to set a target humidity level or range, and have you take care of…
-
Note Option
I would find it really useful if there was a note field for each device. When changing batteries if I could record when I actually change batteries it would help understanding how long they last before replacement - could obviously also be used to record any other useful info.
-
Humidity on app home screen
it would be very useful to show not only the temperature, but also the humidity of each individual thermostat on the app home screen
-
Active/Passive mode for TRV's
Whilst running the TRV's last year I noticed a couple of issues. 1 - As each TRV called for heat at slightly different time, the boiler was constantly having to bring water up to temp to heat an individual room 2 - To try and avoid this I was having to set heating much lower in parts of the house increasing the risk of…