-
2 TRV in the same room
Hello, I have a room with 2 radiators therfore I installed 2 TRVs, selected one as the "Measuring Device". My expectation was that based on the temperature measured by the "Measuring Device" both TRVs will open-close eactly at the same time and be set to the exactly same state, however I can feel that one radiator is warm…
-
TRV not calling for heat
Brand new install into an old house that I've recently moved into. Our Boiler is the garage, connected to an extension kit. Thermostat is in our kitchen, with two TVR radiators (TADO). All radiators else where in the house have Tado TVR - configured into seperate rooms / zones with single TRV / Radiators. All online and…
-
Suddenly Jump in Temperature settings
I was just in the tado app - looking and not touching the screen (I think) and suddenly every room (I have 5) immediately shot up to 20 degrees. I normally have them all set at 17.5 on manual only (ie no schedule). Pretty sure I didn’t press anything - so I can’t understand what happened ?
-
Underfloor Heating Spec
Hi Apologies as I realise there are a lot of UFH heating posts but I couldn't find anythig specific to my query. Essentially we are getting some rennovations done and we are adding some wet UFH to our downstairs kitchen and hallway. I want to add Tado to the rest of the house (as I have had previously) and my question is…
-
TRV reading but not actuating fully
I have a separate lounge and dining room with an open doorway between. Both are on identical schedules but the lounge is controlled by a temperature sensor and the dining room by its trv. The dining room trv appears to have virtually stopped actuating the valve and is letting the lounge to heat it up. Occasionally the trv…
-
Using the add on smart thermostat wirelessly
I have a boiler that has 3 controls; hot water, radiators and underfloor heating. I've bought the wireless smart thermostat starter kit with hot water control for the hot water and radiators. Can I use the add on smart thermostat wireless to control the underfloor heating - will it connect with the wireless receiver from…
-
Buderus Logamax U154-20K wiring
I have this my bathroom - it has a mains power going into it, but there are no plug sockets to power the TADO in addition to the boiler. My questions will seem likely childish or simplistic but Im not an engineer and the TADO installation app for this model doesn't make a great deal of sense unless they mean simply to turn…
-
Suitable Sensor placement
Courtesy of the cleaning robot this is the layout of the flat. Each room has a radiator with a thermostatic valve - each valve is manual and probably 10 years old. Rooms 2,4,7 are bedrooms and don't really every need to be above 18 degrees. Their valves are usually set at about 2. Room 8 is the bathroom and it would be…
-
Heating only works with hot water
Hi, I installed the v3 wireless starter kit yesterday, replacing a Danfoss FP720 controller, but the boiler doesn't fire up for heating, even though the light comes on the receiver. However, when the hot water comes on, the heating also fires up and ignores the thermostat setting, so just stays on until I turn the hot…
-
Tado Wireless Starter Kit V3 Issues
The system is replacing my current Potterton Programmer EP2002. Central Heating start only when Hot Water is ON, else the Central Heating signal to the boiler does not kick start the boiler. Any idea please?
-
Smart TRV not working as expected
I’m hoping someone can point me in the right direction and explain why 2 out of my 6 Smart TRVs are not behaving as I have programmed them to. The setup I have is: Wired Thermostat in the Living Room (had this years and decided to invest in the TRVs). On Tuesday, fitted the new TRVs, set up and connected easily and call…
-
Tado learning period
Apologies if this has been answered before, I couldn't find it in search results so here it goes: How long does Tado initially take to learn the heating properties of a room? Is this an ongoing process? For example if something has changed the dynamics of how long it takes to heat a room (bleeding radiator, increasing…
-
Tado ignored temp settings and turned heating on by itself
Hello, first time here asking questions… hope this is not a too dumb one. I had turned off heating (put tado in frost protection mode) during the holidays because my guests were away. This morning (no one home yet) I got an open window alert and found out the heating had been on (to 25C 😱) since last night at 10.30pm. How…
-
Installed wireless receiver to replace Honeywell one, now no heat boiler not firing
Hi, the Tado thermostat radiator valves were working with my previous wireless receiver but upon installing the Tado one, despite it connecting fine in the app, the radiators and boiler aren't firing up. Any ideas before I try and revert back to the old Center system to get some heat back?
-
Smart AC and HomeKit - understanding what’s happening
Hello. British guy here, which means the concept of air conditioners is fairly new to me. I have one - a Daikin model - in my office, and I’m controlling it from my Tado. I’m trying to understand some of its behaviours, across the Tado app and HomeKit. The first thing I’m stuck on is this. Today, I’m set it (via Home) to…
-
Tado Wired Thermostat Installation
Hi I've currently got a Nest Thermostat E and want to replace it with Tafo which I thought would be easy enough, I moved Com from the Nest to Com on the Tado and NO to NO, however when powered on it seemed to constantly request heat from the boiler. Put the nest back in and everything worked as expected. Anyone any ideas?
-
Missing NO NC COM terminal block - is that normal?
My Tado v3+ Wired Smart Thermostat arrived "new in box" without the left side NO NC COM terminal block. Is that a normal configuration of the product? If not, does anyone know where to get a replacement? It should be a pretty inexpensive part!
-
Why is my TRV
Why is my bedroom TRV not calling for heat when requested, I've noticed it's heating up the same time as the wireless thermostat down stairs as if it's not it's own 'zone'.
-
Wiring up the boiler
I've wired up the wireless receiver to the boiler but I was wondering if I should have disconnected the existing wires that were connected to the boiler for the old wireless thermostat? TIA
-
Tried everything, can’t subscribe.
I tried everything but the appstore on ios just plain sucks. Since you dont offer the subscription here i simply can’t subscribe. Consider adding your own payment system. It’s crazy that i have to put in any effort to pay.
-
Questions on basic concepts with how boilers are managed.
Ive been trying to work out how TADO manages eg Open therm on a boiler. Myvery simple combi boiler, for example, has what appears to be simply the main power coming into the circuitboard, from that there is the circulatory pump wires and this appears to be tripped on and off by the return temperature of the water via the…
-
Stuck in an endless installation loop
I have two starter kits and I de-initalised one internet bridge and installed another. The second unfortunately has decided to go into an endless initalisation loop. Neither bridges can be removed from the app so its a bit of a mess. What next?
-
*Deleted
*Deleted (Not sure how to remove posts)
-
Would you buy Tado goods if you knew no callcentre and they take on day to get back?
-
App not working
Hello Anybody else having problems with the app not connecting to the server started last night
-
What wire connections to make with the Tado Thermostat?
Hi, Attached is my current thermostat and how it's wired. I can see a lot of wires with different colours so it difficult for me to figure out which wires to mark with Tado stickers to go into the Tado thermostat. Any help? Thanks, 07584562979
-
Geofencing radius
The app recognised we had left the house and set the ‘away’ mode with the default 400m in the geofencing settings. We travelled 50 miles north for the day before returning. I understand the iphone sends my location to the app so it recognises we are returning but how many miles out will it set to ‘home’ mode, I cannot see…
-
Modular connection
Hi, I have change my heating to modular connection to +/- but now boiler is not heating. I thing I need change it in APP or somewhere. Can you help somebody?
-
Tado and Vaillant EcoTec
Recently I have replaced my boiler with Vaillant EcoTec plus vcw 346. It is connected to my tado thermostat via ebus. It seems to be working in that when the thermostat calls for heat the boiler switches on and starts working. The problem is, whatever the temperature in the flat is and whatever is needs to be the boiler…
-
Smart TRV fallen apart
One of our TRV stopped working. I just took it off and the pin has become detached. Can this be fixed? Seems thatt it cannot be screwed back on without dismantling further.