-
Tado EU version with hot water control
At the moment I’m having a new central heating system and boiler installed. Unfortunately the heating engineer is unfamiliar with Tado and wanted this plumbed in as PDHW/X-Plan so I could take advantage of opentherm but has plumbed in as S-Plan. Will get this switched to what I want but for now I have a Tado EU version…
-
Danfoss TP9000MA-Si + TS2 Sensor Replacement
We have an Ideal Logic 15 boiler with a single zone S Plan heating system controlled by a Danfoss TP9000MA-Si with a wired TS remote sensor (which is not ideally situated and not easily relocated). We would like to replace this with a Tado kit that would include a non-wired thermostat. Note: As well as connections from…
-
Wired v3 thermostat not reaching programmed temp
Hi, my tado has started playing up. I have it set to heat up to 21º, and it's on for 2 hours. Normally, it reaches that within that timeframe; it only heats up 2-3 degrees, so after 2 hours, it may be 19º at the highest. I have taken the batteries out and unplugged the bridge and set it up again, but it's still the same.…
-
What additional Tado kit do I need to add control for a single wet UFH zone?
Hi. My house is currently set up as follows: Combi boiler for all central heating (and hot water). I have the 'Wireless Smart Thermostat Starter Kit V3+ with Hot Water Control' setup to run the central heating. We don't use the hot water control but needed this setup as the thermostat is not wired to the boiler. Let's call…
-
Home/Away (Geofencing) not starting heating until the person actually arrives home
Hi, Recently installed a Tado X system and the home/away seems problematic. On the previous Nest system we had, Home/Away detection worked out how long it would take to heat the home, and when it detected you were on the way home (from past activity, e.g., it's a weekday, and you're at work, and now you're leaving and…
-
Ebus on Vaillant Ecotec Plus 831 Combi & V3+ Wireless Starter kit
10 years ago I had a Tado installed on this boiler & VRT360f, this was wired for ebus. I initially had Tado system on subscription, and it was getting quite expensive to change to ownership, so I switched to Hive (bad decision). Anyway I have just got myself the V3+ starter kit and have installed this wired for normal RT…
-
Schedule
Why is it when I want to set my schedule the end time jumps backwards to approx 15 minutes after the start time?
-
Tado X wireless receiver without internet connection
Hello, I just bought the Wireless Smart Thermostat X starter kit (Wireless Receiver X + Wireless Temperature Sensor X) with some smart radiator valves and I thought that without an internet connection they would just follow the normal schedule. But I tried and even if the valves and the wireless thermostat can talk to each…
-
Tado V3 Starter Kit
Hi wonder if anyone can help advise me please Would a Tado V3 Starter Kit be compatible with the following make of boiler - any advise greatly appreciated I have a Potterton Performa 30 HE Combi Boiler With A Wireless Thermostat - Also Potterton Make Has anyone fitted the Tado V3 Starter Kit to this type of boiler ? See…
-
Guide for replacing faulty Tado wired smart thermostat with a new one?
I've 2x Tado wired smart thermostats (upstairs and downstairs heating) and 1x extension bridge (for hot water) The downstairs smart thermostat went offline a few days ago and won't come back. It controls heating downstairs and the hot water via an extension bridge. Tried all the usual re-pairing, moving the bridge beside…
-
Radiator balancing
1) Any thermometer suggestions for balancing radiators.? 2) Once you have smart TRVs is balancing still needed as they will regulate flow from the front end rather than the outlet from the rear end of the rad? cheers
-
Merged: Tado App not launching on iOS 15.8.3
This discussion has been merged.
-
Geofencing not switching heating on/off
When I leave home and check the app in the office it shows me as 'away' but it doesn't switch to the target temp (14c) it just carries on with the scheduled temp (20c) If I manually change it to 'away' in the app then it does change to the target temp of 14c
-
Radiator thermostats needs new batteries every 2 months - is that normal?
I installed 8 new radiator Thermostats at the end of Sept 24 and within a month one of them was asking for new batteries which I didn't think too much of at the time as I thought the provided batteries were just poor quality so I replaced with duracells. Now I'm getting the same low battery needs replacing again so within…
-
Boiler water temp too low
Hi, I have a wireless temperature sensor X connected to my Viessman Vitodens 100-W b1kc. In the app, I cannot change the maximum flow temp, either with optimisation on or off. The water temperature remains too low to heat our living space (older house with moderate insulation). I have used the opentherm connection as…
-
App trouble
Hey 👋 I have a problem with my App ! The room name is missing ½ off the last line ? The problem started for 2 week ago !
-
Tado X offline a lot
I’ve been using my Tado X for about a month or so now. It’s been all working okay-ish but lately I’ve noticed that the system is going offline often, which is super inconvenient on these colder days because somehow the offline schedule function doesn’t seem to work at all and when I manually turn the knobs, they won’t work…
-
ATAG boiler giving C151 and not picking up the demand with Tado X
Hi, I am using tado x with ATAG E223 boiler from 2014. Having underfloor heating downstairs and radiators upstairs. Have bypass installed and trying to keep only bedroom warmer in the night but the boiler cannot pick up the demand and temperature goes down with boiler giving C151 error. I have tado x wired thermostat…
-
Vaillant VHR 24-28 keeps heating
I, just installed Tado v3 and my even though the app does not show Tado is giving a heating signal my Valiant keeps heating up the house…I used to have a Toon from Eneco (using OpenTherm) working fine. Any suggestions?
-
Early Start learning (Tado V3+)
We have a room which takes over 3 hours to heat up if the outside temp is below 2C and then it may not hit target in that time. Here in the UK during the recent very cold weather, I have been boosting the room heating with a fan heater for an hour or so to get the room up to temp, then the radiators are able to maintain…
-
Weird goings-on this morning – App/Internet Bridge/Smart thermostat - what's happened?
Got down for breakfast to find the room a bit chilly. Checked the app to find the dining room online but all other rooms offline. How can that be? Changing the temperature in the app had no effect so went to the main, smart thermostat. Upped the temperature manually and the heating came on. But the thermostat showed low…
-
Heating turning on via boiler panel but not via Tado App
Hi, I have the Tado v3 installed in a Worcester Greenstar CDO Classic Combi boiler. When the electrician installed the Tado setup he removed the control panel on the boiler as the control would be now via the Tado app. I was told I could get a blanking plate from Worcester Bosch to go where the control panel used to be.…
-
One receiver with two temp sensors?
Hello, I've just had a v3 wireless kit installed; one bridge, one receiver, one wireless temperature sensor. I'm trying to confirm if it is possible to link a second (or more) temperature sensor to the same kit. I would have the sensors in different parts of the house, and if either of them fell below the target temp, they…
-
help please - no heating
so we've had Tado for several years, we had whatever version it was where you could pay a one off amount to upgrade - I think we had V3 and upgraded to V3+ but I'm not 100% on if those are the right numbers or whether it makes any difference to this. Tado has worked well ever since, we have a wired wall thermostat and…
-
New Tado X compatible boiler recommendations
I currently need to buy a new condensing boiler (EU/CZ, wall-mounted, 24 kW, one heating circuit with radiators+ external DHW tank) compatible with Wireless Smart Thermostat X (i.e. OpenTherm or some API). Wireless thermostat X I already have. Any recommendations? Thanks.
-
Tado X valve discount not calcolated.
I have already ordered 11 valve but I realize now that I need one more. From the site it seems that the price is 99 euro with the discout 66 euro but when I put in the shopping cart the price goes to 99. Why?
-
Tado v3 not connecting to virgin media Hub 3
We recently had a new hub router after the previous one failed. We previously had issues and the tado installer had to do something with the settings in the router (turning off 5g as Tado runs on 2.4g). Tried that to no avail. Has anyone else had this issue and how did you resolve please?
-
Replacing Hive Mini with Tado v3 wireless starter kit
Just moved into a new house where the previous owners had a Hive Mini connected to a Glow Worm 18si boiler, they also left an old thermostat connected. With the old thermostat connected the Hive just controls turning the heating / hot water on and off which works fine. I have purchased the Tado v3 wireless starter kit with…
-
General set-up question
Hi, I have just installed TRVs on all my radiators apart from the towel rail in the bathroom. Initially I turned off the zone controllers as I was finding that the heating was randomly turning itself on and off. However, I want to be able to turn on individual radiators when I want to. My plan is this: turn on the zone…
-
Boiler on, boiler off... hot water taking ages to heat
Hi, I have been lurking here for a month or so since installing the Tado X. Replaced a Drayton LP722 which is connected to a Glo-Warm Flexicom 15HX There are no extra connections to the Boiler (I am aware of a wireless device that can connect) I followed instructions as per the Tado X installation notes and wired…