-
energy efficiency defaults
People on this board will know how to use their thermostat, but... thousands (perhaps millions) of programmable thermostats are sold every year. The problem is that many people have no clue how to program them. One solution is to pre-program the thermostats with energy-saving settings as the default. With a few lines of…
-
more than one property
It would be so helpful if one could flip between two different places, each with the Tado system installed, without having to sign out of one account and into another.
-
fahrenheit/celsius toggle
Hello! We use Tado at home & are quite happy with it. It is not linked to Alexa or Apple Home or any of those fancy things. We just use the Tado app. It would be great if there was a toggle in the settings where we could change the temperature from celsius to fahrenheit or vice versa. I checked the forums & there wasn't…
-
More control to Tado Balance
Hello, Bought Tado V3+ yesterday to control my old Mitsubishi air heat pump. Primary reason is that I use spot priced electricity. So I subscribed for balance immediately. I also use Themo smart home thermostats for my electricity floor heating which also uses spot price. What Themo can but Tado can't do is to anticipate…
-
Zigbee
Zigbee enabled Thermostats ASAP, and as a free upgrade please.
-
Electric towel rail controller
I keep hearing that in the UK, a huge amount of energy is wasted through the inefficient use of electric towel rails. Namely, they are dumb with on/off switches and are not managed alongside the heat output of the main central heating system. Therefore they are left on for long periods. Tado, how about producing an…
-
Use the zone controller name in the selection list
When you select the zone controller for your radiator thermostat, you only see the serial numbers. Can you show the room name of the controllers as well? That would make it easier to select the right one. Oh, and while you're improving that screen, there's no need to repeat "When this room calls for heat, this Zone…
-
Temp graphs in web version
Web version does not show the nice temp graphs that the app versions do. This should be added also to the web versions.
-
Connect to existing wireless receiver
I have searched this forum and looked at installation videos and general searches. It seems that despite many heating systems having wireless thermostats for turning the heating on and off, via a signal to a receiving box wired to the boiler, your system requires replacing this receiver with some slightly scary rewiring.…
-
Energy IQ cost to account for standing charge
I find the estimated gas cost estimate to be reasonably good, but the cost shown is for the consumption cost only. It would be useful for option to include the cost of daily standing charge such that the total month prediction / comparison reflects the total bill for gas not just the consumption.
-
Standing charge for energy IQ
It is well know factor within UK for all the providers to charge daily charge (standing charge). Could you please include this option within Energy IQ to be able to set and see the graph with or without (with slider ON/OFF)to represent monthly charges. This will vastly improve accuracy or shown readings in correlation to…
-
Standing charge
It would be nice to add the standing charge as a feature.
-
Full TRV child lock
The TRV child lock is great for keeping the room set point unaltered but the TRV still lights up when played with. This is enough to keep my daughter entertained and means no manner how many times we move her away she still wants to play with the TRV next to the potentially hot radiator. I propose extending child lock with…
-
Short Boost
It would be very helpful if there was a ‘short boost’ feature, allowing users to turn a device on for a set period only (eg 30m). In my case it would let me heat my hot water outside its schedule without having to remember to turn it off again.
-
Multi Property Support
As a lettings agent, we'd like to be able to install Tado in several properties and be able to access them all from the same app, which we understand can be done by other systems. Is this something that is been worked on for the future, or will it never be implemented ?
-
Extend your gateway coverage
For those who are desperately asking Tado for years to add some range extender option to their product line-up, what follows may be worth reading :-) Recently, as I was in the process of adding TRV's in rooms located in my attic, I faced the "good old" historical coverage issue of Tado's gateway. The big issue is the fact…
-
Tado Widget
I don't understand why there isn't a widget for the app, to be able to see the situation at a glance would be easier that opening the app every time.
-
EnergyIQ to include Hot Water usage as well
It would be great to see Hot Water usage along the heating in EnergyIQ. Thanks
-
Show current temperature on TRVs
Would it be possible to have an option to show the current temperature on the TRV? I have the child lock enabled on all my thermostats and when you spin the wheel it flashes the programmed temperature. It would be nice if there was a way to nudge the dial and display the current temperature without having to open the app…
-
Show hardware version in the app
Simple suggestion, display the hardware version in the app along with the rest of the device settings. It might save a lot of support queries looking for this information!
-
Better control of away mode
Hi! I'm using my AC as a heat source for my summer home and away mode is very important for me. "Away mode" is not just "over the day", "while at work" in this situation but the major mode of operation. The problem I have is that you can't create time slots in away mode, so the AC have to stay on and cost money more then…
-
Change room colour in app when heating
Can the app be changed to highlight those rooms that are heating
-
Customers' data and statistic processing, storing, keeping and access
Dear tado° (community) I have a feedback-concern regarding privacy in your service. Recently I had a case with a malfunctioning (I believe so) thermostat head device. While the discussion is still going in that thread, I have another concern: during our conversation the support engineer mentioned: > The last time your…
-
Make Auto-Assist and Energy-IQ tiles active upon subscription activation in the Tado app
Hello, I activated my annual Auto Assist subscription yesterday, but the Active-Assist and Energy-IQ tabs remained the same (advertising the service). I had to contact support about this, just to be told that it is expected behaviour, and that data will get populated after a month. While that makes sense, it also makes for…
-
Smart home automation
Is there a way to set trigger for when humidity is at the set level to send notification via Alexa or Google or any third party integration? Ideal would be to look at the humidity inside and compare to weather forecast humidity level and if outside is lower than inside send notification to Smart home devices or phone to…
-
Boiler cool down period
Hi, There is a huge need for boiler cool down period. Similar to what Honeywell do, so it doesn't fire up every few minutes again as heat being called for each instance but waits 15-20 minutes in between finishing boiler work and starting new heating cycle. Maybe this is already happening not sure but I have feeling that…
-
Users with different roles
When looking at the user configuration it would be good to see that not all users have full control over the whole system. I am thinking about (for example) 2 roles: An Administrator role and a user role. Obviously, the Administrator can do everything. The user role can be connected to specific rooms and control that room.…
-
Hot Water control in Apple Home
Please enable a Hot Water control in Apple Home.
-
Real window sensors from tado
We would like a real window / door sensor for the "window open function". The current detection of the open windows via the thermostats works so far quite well. However, we have discovered some problems. 1. In some rooms the detection of an open window does not work or does it too late (e.g. bathroom, room with balcony or…
-
Homekit + manual installation for iOS devices
Besides the homekit integration flow also allow iOS users to set up a device using the Android flow. in order to prevent issues like described by jamieb https://community.tado.com/en-gb/discussion/1270/smart-ac-control-v3-without-homekit