-
Zusammengeführt: Smart Ac control 10°C setting
Diese Diskussion wurde zusammengeführt.
-
Support 2 point calibration for adjusting temperature offset (Temperature Guesstimate)
It would be very helpful to enable 2 point calibration for adjusting the temperature measurement to match the middle of the room. Scenario as follows: At low temperature the thermostat reads the same as the temperature measured in the middle of the room e.g. 15°C so no offset required but at higher temperature the…
-
Show humidity as sensor in homekit
It’d be really useful to have the humidity from my tado devices show up as a sensor in homekit. This would allow me to add automations with other devices (eg when humidity goes above a certain level, turn on the dehumidifier)
-
Please implement the possibility of disabled the three LED lights of the internet bridge
Hi Everyone, the Tado internet bridge has three very bright LED lights. I would like to have the possibility to disable those LED lights please. A configuration as described below could be useful for all users: by default, after booting, the LED's are also on but in the app and/or the web portal you can choose to disable…
-
Merged: Spring/Summer and Autumn/Winter settings
This discussion has been merged.
-
Activate open window detection with external window sensors
I would like to be able to use my window/door sensors to activate ‘open window detected’. This would be a great improvement as it will speed up this process and will keep ‘open window detected’ on until I close window/door. I know this can be done indirectly by setting the heater to “off” with ifttt but this means that it…
-
iPhone/Siri Shortcuts Support
TADO application doesn't appear in Siri/iPhone shortcuts. This application is very powerfull and, though complicated to use, can do much more than IFTTT in the Apple world. Tado must support Siri shortcuts. Homekit is obviously supported and a few (very limited) number of things can be done that way. Please support me.
-
Status of each thermostat valve position
Build a function into the settings menu where you can see the status of each thermostat, if the valve is open and how open it is. It would be nice, when you are troubleshooting.
-
Radio signal information
Show information about signal strength between each component and the bridge, so as to have an idea of where to put the bridge to improve the connection with the other components.
-
Real window sensors from tado
We would like a real window / door sensor for the "window open function". The current detection of the open windows via the thermostats works so far quite well. However, we have discovered some problems. 1. In some rooms the detection of an open window does not work or does it too late (e.g. bathroom, room with balcony or…
-
Expose official API and publish documentation
There are multiple home automation platforms available. Some of them make use of reverse engineered API and the main concern is such access would be blocked by Tado at some point or changed. Dear Tado, be brave! People like open products and your market share and brand rating would definitely grow with such API officially…
-
Give users access to the advanced configuration parameters
As most of us here will be aware, Tado has several advanced controls and configuration options that support are able to use to configure your devices when you contact them (cycle periods, minimum on/off times etc). Sadly these advanced options are hidden from users and the only way to access them is through support which…
-
Improve Internet Bridge so it reconnects automatically
The Internet bridge often disconnects from the Internet leaving the Tado system unusable. Please improve its firmware so it reconnects automatically as every other IoT I have does. Currently, the only option is to power cycle which is unacceptable when it happens at 4am, and we wake up to a cold house....
-
Plot all rooms on same graph
Perhaps with selectors to show/hide rooms. Would be great to see the interaction between temperatures!
-
Add the heating level indicator 1,2,3 bars to the Home Screen in each room
For a quick overview of which rooms are currently heating it would be useful to see the three bars indicator for each room on the Home Screen.
-
Support one decimal place (0.1) for radiator valve temperatures in the Tado app
These devices appear to report their temperature at 1 decimal place of accuracy (I see it via the API in my Home Assistant integration) yet the Tado app only shows their temperature as integers. Can you please change this? I recognise this might be difficult on the device display itself but not in the app. I'd also like to…
-
Improve "Climate Report" graph
The horizontal grid lines in the "Climate Control" history graph currently behave very inconsistently and are not very clear to work out the temperature from. There are three fixed lines, the top and bottom have a label which varies depending on the range of the currently displayed graph, but by having fixed lines, this…
-
Create a range extender or let us use a second bridge...
Having olny 1 bridge per house is a massive design flaw yet to be addressed by Tado. Unless you leave in a tiny house made of cardboard walls, the TRV wlll lose connection or burn batteries in only a matter I'd a couple of weeks. I live in a house across 3 floors, I really struggle with the range and can't have full…
-
Support newer version of Worcester HT-BUS
I just upgraded from a worcester bosch greenstar cdi to a worcester bosch greenstar 8000 life. On my old boiler I could connect to the digital low voltage interface bus however the new boiler the ht-bus is not supported and I couldn't simply change over I had to rewire to the old relay style. The bus interface is better…
-
Different Scenarios for Heating Schedules
Loving the Tado (but hating the 10 room limit) and I would like to make a heating scenario suggestion. This is to allow simple, perhaps temporary, changes to the heating schedule according to a set programme based on scenarios. The current way of working is to set up one scenario of daily heating and any changes require…
-
Improve heating algorithm to wind down heating power earlier, to prevent temperature overshooting
In using tado radiator valves and thermostat, I notice they almost always overshoot their intended temperature. That's usually because the heating power will remain at full strength almost until the temperature is reached. It would be better if the algorithm supports earlier wind down of the heating delivered so the…
-
Support current and more recent Vaillant eBus controllers
Tado asserts the benefits of modulating boiler control and touts compatibility with Valiant and eBus. However, the reality is rather grim. It turns out that as of 2019-03 eBus is only supported in these scenarios using the now discontinued VR65 controller. No other controllers are supported (VR66 for example). This means…
-
Please bring back “Until next automatic change” in the app manual mode
With the release of App version 5.11 that aligns the UI of V3 and V3+ You have have removed a feature that I found really useful. With the old app I could set a temperature in manual “Until next automatic change”. It would remain in this mode until either a Smart Schedule event occurred, OR I LEFT HOME, see image. With the…
-
Hot water monitoring & Tado hot water tank thermostat
Hi, I'd like to be able to monitor our hot water, so I can see when the hot water is requesting heat from the boiler and ideally see the temp of our cylinder tanked hot water. The app shows simply off and on. We have the Extension Kit controlling our heating and hot water. There is no way of telling when the hot water has…
-
allow changing the name of devices
Please allow us to change the names of devices to make it easier to identify them. For example, getting an email that tells me: "We have noticed that the batteries in your Smart Radiator Thermostat VA*******048 in the zone ****** are running low." I have 15 devices and if each device had a name I wouldn't have to waste…
-
Changes to the Firmware Update System
Instead of having to contact support to see if an update is available and getting a massive statement about "staged rollouts" and allowing you to "address issues early" - I still think the app should show if updates are available but state that it's rolling out, and then people won't have to contact support to see if…
-
Hot water temperature monitor via extension kit
My heating system is the hot water storage type where a larger tank is used to store hot water for heating the radiators and hot water supplied via a heat exchanger. The tank is heated by a solar panel on the roof and a wood burning stove. Backup heating is via a gas boiler, which is controlled by Tado. It would be good if…
-
Bring back Modulation (OpenTherm) to their wireless thermostat (UK)
Currently only the wired version supports modulation (OpenTherm) where as the wireless version in the UK ONLY does not support modulation. The EU version does. I think Tado should bring the EU version features to the UK product. It's essential for energy saving and would add more competition to the market and make Tado…
-
iOS Widget for Tado app.
iOS Widget for Tado app.
-
Support for the EMS2 bus - Bosch Condens
Bosch / Junkers / Nefit boilers with the EMS2 bus have been on the market for many years now, have a large chunk of the European market share but Tado only supports relay operation for them. I myself have a Condens 2300i boiler and while the relay mode works up to a point, the TPI algorithm operating the relay can't avoid…