It’d be great to have an option to add future dates and times when you know you’ll be leaving home in the morning, so that the system doesn’t start heating full on. Since that’s not the same everyday,…
When I say I'm going away, it would be helpful if it let me say until... Eg I'm away - but I'll be back 2pm on Tuesday 7th. It might pop up or email me 24 hours before and let me change that predictio…
Hi, Hopefully not the biggest amount of work for this one: It would be nice to be able to define “when” you want to get notified from Tado to submit an energy reading. For weekly notifications it coul…
Would love to see the Tado Internet Bridge with Power over Ethernet. This could save us an additional cable because everything can be done with the Ethernet cable. Since the raspberry pi and many othe…
It would be very helpful to enable 2 point calibration for adjusting the temperature measurement to match the middle of the room. Scenario as follows: At low temperature the thermostat reads the same …
The "Intelligent Climate Control Device V3+" should be able to be associated with the same room as a thermostatic valve and be chosen as the reference for the external temperature. This can be done si…
Currently the beta “estimated energy report” appears to be fixed as EUR currency. This should be configurable so users can select their home currency e.g GBP
My GPS is behaving a little bit funky, and the Tado App doesn't set my Home correctly in the Setup Procedure. Thats why I would like there to be an option to manually set the home location.
For district / city heating the bill and meter readings are in GJ. It is very annoying to have to manually convert the units. Should be an easy fix: 1GJ is 277,8 kWh or 31,6 - 32,68 m3 gas.
When no heat is requested, the pressure in the system can be so low, that the radiator valve pin does not spring out fully. This can result in an E4 error, or invalid calibration. This can be manually…
The included 30 cm power wire and ethernet cable contradict the advice that optimal positioning of the bridge should be vertical and not directly behind the router. It is very hard to get the bridge i…
A command to restore the schedule both by room or whole system is vital. I keep forgetting to manually restore at night and wake up to cold or too hot rooms. This command could be used as part of a 'g…
Tado speaks about being environmentally friendly but my radiator thermostat broke. The resolution is to share a receipt and they ship me a new one (across multiple countries) and then I return mine (a…
I noticed that tado is not good at keeping a stable room temperature. Instead of turning the heating on in advance while temperature is dropping close the level, it turns on when it’s just below. But …
It’s usually lot of waste of heating when heating is on level 3. Tado is not able at effectively run preheating economically. Its ability to learn this effectively gets complicated as the many things …
The tab colours are great but the schedule summary bars are not. Can you change the schedule colours to match the tabs? Example: 18 degrees on a tab has a clear distinct colour but on the schedule bar…
Thanks to tado, my 25yr old house is keeping the target temperature for the first time and the overall heating cost are down. I love it! A few suggestions: 1) The valve opening (%) should be visible a…
Much like the boost heating option, it would be nice for an option to reduce the heating for a set amount of time. Sometimes I find myself doing housework and then the house gets too hot. I only have …
There is currently a bug in the activity graph after a temperature target is changed via Homekit (in this case specifically Siri). The activity graph fails to show the correct categorisation after the…
The air comfort page on the app and website doesnt appear to be that intelligent. Its telling me various messages about ventilation and not drying clothes in the house and extractor fans etc etc. but …
Ik ga van huis, uit logeren. Maar niet verweg. Ik wil tot een datum/tijd dat het HELE huis op een bepaalde lage temp staat. Want, het probleem is dat ook als geolocatie op zeg 5 km zet en je bent 15 k…
When valves open a tiny amount in a single zone they are noisy I would like to be able to set a minimum opening value. This would largley solve the issue but i'll go into it in more detail as I have a…
Hi, Ik loop er tegenaan dat ik meerdere woningen wil bedienen. Echter is dit nu niet mogelijk vanuit dezelfde account en moet ik een tweede account aanmaken voor de tweede woning. Daarnaast moet ik bi…
1) Show all devices on a single page in a graph 2) Show the graph as above but showing 1 week, 1 month etc intervals? 3) is there an external Tado device that can be installed to indicate the true out…
Tado do not make/offer a black stand for the black temp sensor. I don’t understand why not but would suggest that’s an obvious (though minor) omission from their range. I have sourced a 3rd party stan…
You can set a temperature offset but usually the offset is different depending on the actual room temp - so offset usually is accurate for high or low temperature but not the other (due to non-linear …
Hi Please consider using wireless thermostat as an auto calibration offset tool within a room. Now have TRVs on all radiators. Put wireless thermostat into the area of the room I'd like to adjust the …
The schedules are real flexible but sometimes you need to boost the temp. This you can do easily via the app or stat. What would be usefully would be able to select return to to normal automatic sched…
I already contacted TADO support and had this conversant with the support agent, they advised me to create a query here as an "Enhancement Request" Basically, my scenario is; I have a large house and …
