-
Tado to start replying back
My idea is for Tado to start replying back to the community. I am seeing posts from YEARS ago ignored. It's time for this idea to be the top one in the company and Tado to listen to it's loyal customer base.
-
Warn about two day instruction wait time with compatibility check
I've just had to change my boiler, and I followed all the Tado advice about asking for a compatibility check. I thought all was good. The boiler installer engineer was here getting towards completion. I went to the Tado app to change the boiler. Found the boiler… and it said something like "Please wait for up to 2 days for…
-
Valve moving when out of heating season
It's usual that the long pressed valve needles are stuck. If the valves move them on a setupable time period (daily, weekly, etc) this should be avoidable.
-
Better collaboration with Air Source heating system
I have an air source heating system in my home and the projected forecast costs are not reflected well at all with the app. I input my energy usage each month and never get anywhere close accurate costing suggestions. The data input screens are clearly for gas/oil systems, and not designed for Air Source systems. Our Tado°…
-
Manually switching off individual rooms
Sometimes it is easy to switch off one room, for example the one that is still cold in the morning but is heated by the sun while nobody is there. The only way to do this is to turn the temperature down, or first switch off all the rooms and then switch some of them back on.
-
Temporary extend current schedule
Time to time I get into the situation when I know I will work a bit longer in my work room. Currently I can do two things to extend the heating, 1) wait until the switch and then set to the same temperature as before with a (optional) time limit 2) set the temperature +/-0.5C before the schedule switching off with…
-
Self installation
We have chosen to have our Tado wireless thermostat installed professionally. The pro told us Tado as a product is fab but he says it should not be classed as self installation because once you take off the boiler cover you have broken safety regulations and would need it to be assessed by a professional afterwards.
-
Improve Care&Protect boiler fault detection
The problem i encounter is easy to explain. If for example my TADO is programmed to turn my boiler on (be it automatically or manually), and for whatever reason the boiler is either Off or the mains is down, TADO doesn’t inform that the boiler isn’t on. In this second report I have sent, the boiler was resetting itself due…
-
Change comfort scale
I find 18C comfortable, yet Tado tells me that I’m cold (even 19.5C is considered cold, whereas it’s uncomfortably warm for me). I’d like to be able to change the comfort scale, so I’m not prompted to “put on a jumper”, “snuggle under a blanket”, or “turn the heating up”. When we’re meant to be saving energy and resources,…
-
Fault detection if no temperature change detected
If a room has an temperature increase demand but there is no change in temperature for a given time period a warning should be triggered by Tado. My boiler has an issue that it needs resetting Every soften I only find out after an hour so after i get cold. That the system is not working. But the Tado ‘care & protect’ tab…
-
Reset of meter counter
Hi, I have recently got replacement of meter device from gas company, and it has counter "reset" to some value that is smaller than last value I have entered in application. Current support recommendation is to delete all past records, and to start over from time when this meter was installed - with loosing all history…
-
Volledig open, volledig gesloten instelling
Beste Tado, Het zou zeer handig zijn om een kleine instelling toe te voegen aan de instellingen voor de slimme radiatorknoppen. Namelijk een instelling dat hij volledig open gaat als er warmte vraag is, en volledig gesloten gaat als er geen warmte vraag meer is. Dus een instelling toevoegen voor niet stapsgewijs inregelen,…
-
Themed icon for Android app
Since Android 12 or 13 apps can provide a themed icon that blends in nicely with the new visuals by adapting to the current accent color. Could you please implement it for tado as well?
-
Heating Activity - Real Time
Hello, Whilst "Heating Activity" is good at showing which zone/room is currently heating, what is not in anywhere near real time is the Total Today value. It will sometimes take hours before the Total Today time changes when I know the heating has been on for more than the total of 11 minutes it has kept telling me.. I may…
-
Smaller increments for radiator thermostats
Hi, I run a couple of thermostats on my district heating system. The water temperature to the radiators is controlled by a PI-regulator, that does a good job. However, the Tado thermostats seems in daily operation to make quite dramatic changes to the waterflow through them, which means I see dramatic water temperarure…
-
Night mode for wireless receiver (no lights)
We have installed the wireless receiver in our son's room replacing the previous controller that was placed there. Everything works fine but at night the lights are like so: We need a blackout room for our son to sleep (he is nearly 2 years old) and these lights unfortunately keep him awake. A feature I would like is to be…
-
Temperature cap by room
Can we please have the ability to set a cap on target temperatures by room on the app
-
[Released with tado° X] Support for Matter standards
Full support and integration with the Matter standards https://buildwithmatter.com as the standards develop and get published - ideally without having to upgrade the hub, etc.
-
Leave the valves opened in 1, 2 or 3 gears
Nowadays we can close the valve (OFF) or open it fully (25º), and the control is based only in the temperature that the valve is measuring. The thing is that in my area where it below 0º at night, the valve is constantly opening and closing, with the noise of the small engine attached. To avoid this noise, the idea is to…
-
Pouvoir changer la température hors gel
Bonjour, J'aimerai pouvoir changer la température hors gel par défaut pour pouvoir éteindre mon installation simplement quand je quitte ma maison de campagne pour quelques jours plutôt que de devoir utiliser le sélecteur vertical de température qui m'oblige à changer également jusqu'à quand ce changement de température…
-
Mehrere zuhause pro Account
Bitte bitte bitte, ich warte seit Jahren darauf, dass ich endlich mehrere Tados in einem Account nutzen kann. Mir
-
Electric Radiator Element
There are Wifi controlled elements for electric radiators on the market so assume this is not an impossible request. However, it would be great for Tado to offer this option to link in with the main app (like the AC controls) which can offer heating to areas of a property where no wet heating system is installed. it would…
-
weekly activating of the valves during the sommer periode
Hi. Older heating systems have problems with the valves getting stuck when the heating period starts. This means that I have to dismantle all the Tado thermostats and exercise the valves so that they can work again. It would be an idea, however, if Tado once a week "turns on and off" the thermostats, so that the valves…
-
Have an option to dim or extinguish the lights on the wireless receiver.
The LED lights on the wireless receiver are very bright in a dark room, e.g. a bedroom at night. It would be a useful feature to be able to dim or extinguish the lights on the wireless receiver.
-
child proof fixation of the radiator thermostat
The radiotor thermostat comes loose way to easy. My 14 months old kid had it loose in no time. What is the point of having a child protection mode in the software, if the hardware is not child proof.
-
Airco and heating syncronisation
It would be great if Tado airco and standard Tado heating controls could synchronise in the same room so that heating doesn’t try to heat when airco is cooling. This seems like an obvious feature, but apparently they are two totally different systems in the app. This is a shame as in many cases in Europe the heating is…
-
Use one thermostat to override all system
Hi, It would be good to set one ST or TRV or whatever that when overriding the programmed schedule through its interface (not from the app), it will override the whole system to the specified temperature.
-
Intervals dans progamming
HI, I think we should be able to get interval from monday to thursday for we not need to program every day individually. Because weekend begins when we finísh our worktime and we change our habits
-
Lowest sepoint temp is 16 degrees
On my Mitsubishi AC can i set the setpoint as low as 5 degrees. In Tado app the lowest setpoint is 16 degrees. Make it possible to have lower setpoint in Tado then 16 degrees!
-
Directly select room on the Graph page, without navigating away
Please could a drop down to select each room be included on the graph screen in the App? This would allow quicker comparison of how different rooms have behaved, without having to navigate away to a different room and then selecting the charts again and again. I find the graphs of each room very useful, but find it…