-
38CDI Digital installation
Hi all. I have a TADO and Extension Kit fitting. My boiler is a Woucester Bosch 38CDI. Is there anyway of working out if my TADO is plummed into the digital EMS interface of my boiler. It was installed a few years back and I honestly cant remember. I could open the boiler up but was hoping there is an easier way to be able…
-
What am I doing wrong………
Hi, Have 2 zones setup with wired thermostats and timer to boiler set to on. HW on the same timer and not controlled by Tado is set to auto. Installed the thermostats on Friday and all good. On Saturday I installed TRV’s upstairs and since then the upstairs heating hasn't worked. All TRV’s are set to 20 and show 20 on the…
-
How does it work?
I have a family house with gas boiler, radiator heating and wired temostat in the living room. I woluld like to install a wired smart termostat in our living room and two smart radiator termostat in the bedroom and study. (it can be extend in the future). I think the boiler will start, if the temperature in living room too…
-
Can I get the radiator Thermostat detect open window while using a wireless temp sensor
Hi, So I have a wireless temp sensor taking readings to be more accurate which is on the wall on the other side of the radiator. When a window is open and if its not very windy and cold, my sensor would not even realize the window is opened since the temperature wouldnt drop on the other side of the room. Even if its very…
-
Help have i got the right kit
Hi there I have a vailant combi boiler 2 cables come from this to a switch socket to turn the power off to the boiler, 1 cable then goes from the socket to a wired old dial thermostat, this is all upstairs on the landing where it is always warm and all rads are always off apart from the towel radiator in the bathroom. I am…
-
One TRV stuck open
Hi, I’ve read various similar threads about this. I think it might come down to needing a replacement TRV, but I have a question about how secure/tight the mounting for the Tado smart thermostat radiator thermostat should be. When I have fully tightened the metal ring on to the TRV, the plastic that the Tado thermostat…
-
Worcester B 35CDI
My Worcester Bosch CDI 35 has a wired thermostat on the wall which has 2 wires from the boiler and 240v power supply (owl intuition c thermostat) 4 in total I can tell which the 240 wires are, but The wireless thermostat needs 2 wires by the looks of it, but how do I know which of the two wires going to the boiler go where…
-
2 seperate heating zones in boiler
I have a radiator system working with Tado and extension kit to request pump and boiler start. Using Potential free input to boiler. I also have a underfloor heating system and I have a second potential free digital input to request pump and boiler start for floor heating. Is it possible to Put radiator termostats to one…
-
My thermostat isn't in the same room
Hi, As per the picture attached this is my situation and I'm looking to get more understanding how tado works. My thermostat is located in my hallway and not my living room, there are no radiators in the hallway and kitchen, and the bathroom one hasn't got the tado radiator thermostat. When I set up the system and first…
-
Problems with setting up our radiator thermostats
Tried to install the radiator valve using one of the adapters in the package. When it is not connected to the radiator the two parts of the valve can be locked in place. When using the adapter it wont lock. None of the other adapters seem to work. Has anyone else had this problem please? Any solutions?
-
No hot water Icon showing
Hi, have an extension kit with smart Thermostats installed v3. All working fine. Then I source the same system from else where and changed it over like for like had to reinstall everything using the same face plates (so same wiring config) however now I have no hot water showing in my app. I’ve tried delete home and…
-
Hot water option showing in app, but shouldn't be there?
I've just setup a new wired smart thermostat with my combi-boiler, which mostly seems to be working well, however for some reason the app is displaying the hot water button and allows me to change it's settings. As I have a combi-boiler I assume this shouldn't be active? How can I remove it from the app, and if someone in…
-
Tado smart AC control V3+: How to control vent direction of Mitsubishi Industries AC?
I‘m trying to setup Tado V3+ with a Mitsubishi Industries AC. AC was automatically detected (command set AS-370), temperature, cool/dry/etc. modes and fan mode are controllable via Tado App and Apple Homekit. Unfortunately I can’t control vent directions (up/down, left/right). The AC starts always in Auto-3D mode. Is there…
-
What is the Battery Life for V3 Wireless Thermostat?
I want to know how long the 3 AA batteries should last on average ( number of months ) for the wireless thermostat?, appreciate the answer will be it depends on usage, but I plan on not using the controls on the thermostat but instead use the Mobile App to manage it. Been trying to find out some information on this, so far…
-
Can a "smart radiator valve" temperature trigger "smart thermostat" to start the boiler (CV)?
Hi tado owners, I am a bit confused with the behaviour I see. My simplified setup is as follows: living room is equipped with Smart wall Thermostat bedroom is equipped with Smart Radiator Valve If my living room thermostat temperature is set to 20C, can I set bedroom temp to a higher value like 22C? Or is the smart…
-
Boiler not connecting to Extension kit
Hi I’ve just finished wiring in an extension box to my Worcester Greenstar boiler. It’s powered up and connected fine, but the thermostat isn’t firing the boiler. I have a flashing radio connection symbol on the boiler- indicating, I guess that the boiler can’t connect to the old Worcester digitstat If I put the batteries…
-
Away mode v leaving heating on all day
Hello fellow Tado users. I have recently purchased more smart radiator thermostats. What I want to know is if it’s better to use the away mode for when we are out of the house, or to leave the heating on all day. I guess with the away mode the boiler will need to work harder when we do turn the heating on, whereas leaving…
-
Extension not recognising hot water system
Hi, I'm new to Tado. I've just installed an extension, 8 TRVs and a smart thermostat. I moved over from a Nest thermostat. The heating works fine, but the extension doesn't recognise that I have a hot water system. The extension is wired in correctly and firmware updated to 64.6. I have matched the S-Plan wiring on the…
-
Thermostat wired to mains socket
My thermostat (30-yr-old Hungarian brand) is wired to a mains socket in boiler room, and the boiler (plus separate pump) plug into that. Would I need a wired or wireless starter kit?
-
Heating not switching off
Hi Everyone, After some help, I have just had my tado starter kit V3 and an add on thermostat installed by a qualified electrician, all seems to be working fine except that the heating won’t switch off at all, even with both thermostats turned off Has anyone experienced this as well and found a resolution?
-
Heating now switching off
Hi Everyone, After some help, I have just had my tado starter kit V3 and an add on thermostat installed by a qualified electrician, all seems to be working fine expect that the heating won’t switch off at all, even with both thermostats turned off Has anyone experienced this as well and found a resolution?
-
Why does Thermostat not use boiler fully?
If I manually boost my heating for an hour, the target temperature is rarely achieved, but the boiler isn't asked for full capacity ie 1 or 2 bars only. Why?
-
Heating Not Coming On
Hi Had a new boiler fitted yesterday (Worcester Bosch Greenstar i). This was fitted with the Tado Themorstat and extension kit. Internet bridge has 3 lights on, thermostat is paired (the chain links on the display are joined together) and the extension kit light is "breathing". Yet when we turn the thermostat temperature…
-
Do i need smart rad thermostats in the room with the smart thermostat
I have the smart thermostat in my livingroom with 2 radiators. Do i need to equip both radiators with smart rad thermo valves or can i just put open/close valves on them and let the smart thermostat regulate the livingroom temperature?
-
Upgrading from Honeywell AQ6000 controller to Starter kit V3
Hi I have purchased the starter kit v3 and I'm beginning to wonder if it is not compatible with my current system or requires additional parts/modifications (or that most of the sensors wiring isn't required for a Tado installation). Boiler is a Potterton Precision condensing boiler. Currently wired using L,N and E. No…
-
Setting up new system without Internet
My friend is buying a house and moving in on Friday. She will have no internet till late next week. The system in place has been left by previous owner and is a standard smart thermostat and internet bridge, with I think a wired boiler reciever. I have a Tado system in my own house so I know how it works in general. But…
-
Tado Extension Kit to replace Nest V3 (Heat link) ?
Hi, I currently have a Nest V3 thermostat with the Heatlink connected to a combi boiler in the UK. I'm thinking about replacing it with a Tado thermostat and Extension kit after using the radiator valves. Has anyone done this, and if so, was it a straight swap (take out heatlink, install extension kit with simple wiring…
-
Extension kit
I have just bought the full Tado system which I thought was wireless, but it appears the Extension kit needs to be wired to the boiler! I currently have a ideal logic +35 combi boiler in the kitchen with a wireless thermostat in the hallway. No wires go into the boiler or around the house. So assumed the boiler already had…
-
Extension kit and smart thermosta supported power
Hi All, Im installing a thermostat with extension kit. the extension has to switch on the boiler as usual. I need also to power on two water pump circulator ( 220v, 50 Watt ). I would power on one pump with the same extension module and one with the thermostat. can i use the internal switch? can it bear this 220v load or i…
-
Re : Thermostat - programmation intelligente