-
Manual Home Placement for Geofence
My GPS is behaving a little bit funky, and the Tado App doesn't set my Home correctly in the Setup Procedure. Thats why I would like there to be an option to manually set the home location.
-
GJ unit in Energy IQ
For district / city heating the bill and meter readings are in GJ. It is very annoying to have to manually convert the units. Should be an easy fix: 1GJ is 277,8 kWh or 31,6 - 32,68 m3 gas.
-
Improve calibration by requesting heat
When no heat is requested, the pressure in the system can be so low, that the radiator valve pin does not spring out fully. This can result in an E4 error, or invalid calibration. This can be manually resolved by enabling boost heating before mounting the smart radiator thermostats. However, I suggest that the Tado…
-
Heating advance
Hi, This is an old idea that hasn't occurred to Tado as yet. My old school heating controllers have always included a Heating Advance Button. It's a simple idea - if you have a day that starts a bit earlier than usual, you just advance the whole heating programme with a single click, or turn of a knob. The next programmed…
-
Combined bridge power/ethernet wire
The included 30 cm power wire and ethernet cable contradict the advice that optimal positioning of the bridge should be vertical and not directly behind the router. It is very hard to get the bridge into a vertical position and on the wall while not being very close to the router. Tado also suggest the use of powerline…
-
Voice assistant missing command
A command to restore the schedule both by room or whole system is vital. I keep forgetting to manually restore at night and wake up to cold or too hot rooms. This command could be used as part of a 'goodnight' voice or timed routine.
-
Release a smaller, cheaper Wireless Temperature Sensor for the Smart Radiator Thermostats
The recently released "Tado Wireless Temperature Sensor" is essential, in many scenarios, to have accurate operation of the Tado Smart Radiator Thermostats. Which, due to their proximity to the radiator, are not typically able to measure the actual room temperature themselves. However, many find the price (£69.99 / 79,99€)…
-
Become truly environmentally friendly
Tado speaks about being environmentally friendly but my radiator thermostat broke. The resolution is to share a receipt and they ship me a new one (across multiple countries) and then I return mine (again across a long distance) I was told Tado does not have a repair department which begs the question of why it cannot be…
-
Better preseve room temperature
I noticed that tado is not good at keeping a stable room temperature. Instead of turning the heating on in advance while temperature is dropping close the level, it turns on when it’s just below. But that will be too late and thus after some time it increases the power to get the temperature higher which is waste of…
-
Ability to limit heating level for each room or each thermostat
It’s usually lot of waste of heating when heating is on level 3. Tado is not able at effectively run preheating economically. Its ability to learn this effectively gets complicated as the many things affect this such as X if room door is opened or not, or how often door is opened/closed. The temperature outside the door. X…
-
Add the heating level indicator 1,2,3 bars to the Home Screen in each room
For a quick overview of which rooms are currently heating it would be useful to see the three bars indicator for each room on the Home Screen.
-
2023/12 - Change App Schedule Colours to Match Tabs
The tab colours are great but the schedule summary bars are not. Can you change the schedule colours to match the tabs? Example: 18 degrees on a tab has a clear distinct colour but on the schedule bar it is a bland indistinct grey (3rd and 5th block on the right on the attached images).
-
display, max valve opening, subscription
Thanks to tado, my 25yr old house is keeping the target temperature for the first time and the overall heating cost are down. I love it! A few suggestions: 1) The valve opening (%) should be visible at the home screen (right next to room name and room temperature). Important to instantly see the level of heating per room…
-
A reduce heating button
Much like the boost heating option, it would be nice for an option to reduce the heating for a set amount of time. Sometimes I find myself doing housework and then the house gets too hot. I only have the option to turn the heating off and then remember to turn it back on again. With the reduce function I think it could be…
-
Small bug in heating activity graph
There is currently a bug in the activity graph after a temperature target is changed via Homekit (in this case specifically Siri). The activity graph fails to show the correct categorisation after the system reverts to the current schedule (its set to revert any manual changes), or an away state. The following screenshots…
-
Air Comfort telling me my room is too humid !!
The air comfort page on the app and website doesnt appear to be that intelligent. Its telling me various messages about ventilation and not drying clothes in the house and extractor fans etc etc. but what it doesn't seem to be taking into account is the outdoor humidity. for instance - in this screenshot its telling me my…
-
Geoloactie werkt niet als je langere tijd dichtbij van huis bent.
Ik ga van huis, uit logeren. Maar niet verweg. Ik wil tot een datum/tijd dat het HELE huis op een bepaalde lage temp staat. Want, het probleem is dat ook als geolocatie op zeg 5 km zet en je bent 15 km ver weg. Dan denkt Tado “die is niet ver weg, en dus zorg ik dat het huis niet tot de minimale temp afkoelt.” Dus dan moet…
-
Setting for degree of valve opening +/- smart opening relation to number of active zones
When valves open a tiny amount in a single zone they are noisy I would like to be able to set a minimum opening value. This would largley solve the issue but i'll go into it in more detail as I have a more elegant solution as well. I have tado valves on every radiator and if only a few zones are calling for heat then the…
-
Meerdere woningen bedienen vanuit 1 tado account
Hi, Ik loop er tegenaan dat ik meerdere woningen wil bedienen. Echter is dit nu niet mogelijk vanuit dezelfde account en moet ik een tweede account aanmaken voor de tweede woning. Daarnaast moet ik bij het wisselen van woning steeds uit- en inloggen. Ik heb het idee dat meer mensen met dit probleem kampen. IT-technisch…
-
Longer graphs?
1) Show all devices on a single page in a graph 2) Show the graph as above but showing 1 week, 1 month etc intervals? 3) is there an external Tado device that can be installed to indicate the true outside temperature/humidity? 4) Can the graphs be printed?
-
Black Wireless Temperature Sensor Stand
Tado do not make/offer a black stand for the black temp sensor. I don’t understand why not but would suggest that’s an obvious (though minor) omission from their range. I have sourced a 3rd party stand on eBay and it’s very good but would have bought a genuine Tado if it was available.
-
Room temperature calibration
You can set a temperature offset but usually the offset is different depending on the actual room temp - so offset usually is accurate for high or low temperature but not the other (due to non-linear temperature profile of the room from a point not near the TRV). It would be great if I could take the TADO wall mounted…
-
Calibrate offset of TRVs automatically based on wireless thermostat
Hi Please consider using wireless thermostat as an auto calibration offset tool within a room. Now have TRVs on all radiators. Put wireless thermostat into the area of the room I'd like to adjust the temperature to. Have TRVs in room check their offset against that wireless thermostat and adjust automatically. Have this as…
-
Auto return to room schedule when temp has been manually set
The schedules are real flexible but sometimes you need to boost the temp. This you can do easily via the app or stat. What would be usefully would be able to select return to to normal automatic schedule on the next timed change to the room temp. We have had a number of occasions where someone felt cold tweaked the stat or…
-
Allow rooms to be excluded from the 'Boost" option
I already contacted TADO support and had this conversant with the support agent, they advised me to create a query here as an "Enhancement Request" Basically, my scenario is; I have a large house and my kids would usually go to school between 7am and 5pm, I personally stay in to work from home along with my Mrs. When I ask…
-
Smart home connections..
There are two things I would like access to from Hubitat and/or Alexa. Preferably Hubitat. 1.Home or Away settings, both to change and monitor 2.Device calling for heat from boiler.
-
Black edition TRVs
It’d be super if there was a black edition TRV to match the new black edition thermostats - would look nicer on black radiators than the existing white ones IMO
-
Global Device Error History
There's various system errors that are actionable and useful for the user to review for troubleshooting, if only they could review the relevant past historical info in one place focused solely on problems. An error log. lost signal periods for TRVs, sensors, receivers disconnected internet periods for the internet bridge…
-
Feature request: consider central heating schedules
Hi there, I live in an apartment block with a central heating boiler. It does not run 24/7. There is a schedule that can vary every year or on special circumstances. I believe this is a very common situation in Spain, maybe not so much in other countries. So I cannot have the heating on at any time I choose, but only…
-
Make Opentherm boiler specific tweaks possible
Hi! I'm having an issue with opentherm using my boiler Enbra CD34H. After some troubleshooting I found out that issue is caused by Opentherm message ID 14 (Maximum relative modulation) being send too often by Tado (every 6s). Unfortunately support is unable to change this to 2mins intervals (which would fix the issue) for…