-
Please bring back “Until next automatic change” in the app manual mode
With the release of App version 5.11 that aligns the UI of V3 and V3+ You have have removed a feature that I found really useful. With the old app I could set a temperature in manual “Until next automatic change”. It would remain in this mode until either a Smart Schedule event occurred, OR I LEFT HOME, see image. With the…
-
Support newer version of Worcester HT-BUS
I just upgraded from a worcester bosch greenstar cdi to a worcester bosch greenstar 8000 life. On my old boiler I could connect to the digital low voltage interface bus however the new boiler the ht-bus is not supported and I couldn't simply change over I had to rewire to the old relay style. The bus interface is better…
-
Improve heating algorithm to wind down heating power earlier, to prevent temperature overshooting
In using tado radiator valves and thermostat, I notice they almost always overshoot their intended temperature. That's usually because the heating power will remain at full strength almost until the temperature is reached. It would be better if the algorithm supports earlier wind down of the heating delivered so the…
-
Hot water monitoring & Tado hot water tank thermostat
Hi, I'd like to be able to monitor our hot water, so I can see when the hot water is requesting heat from the boiler and ideally see the temp of our cylinder tanked hot water. The app shows simply off and on. We have the Extension Kit controlling our heating and hot water. There is no way of telling when the hot water has…
-
Different Scenarios for Heating Schedules
Loving the Tado (but hating the 10 room limit) and I would like to make a heating scenario suggestion. This is to allow simple, perhaps temporary, changes to the heating schedule according to a set programme based on scenarios. The current way of working is to set up one scenario of daily heating and any changes require…
-
Changes to the Firmware Update System
Instead of having to contact support to see if an update is available and getting a massive statement about "staged rollouts" and allowing you to "address issues early" - I still think the app should show if updates are available but state that it's rolling out, and then people won't have to contact support to see if…
-
Bring back Modulation (OpenTherm) to their wireless thermostat (UK)
Currently only the wired version supports modulation (OpenTherm) where as the wireless version in the UK ONLY does not support modulation. The EU version does. I think Tado should bring the EU version features to the UK product. It's essential for energy saving and would add more competition to the market and make Tado…
-
iOS Widget for Tado app.
iOS Widget for Tado app.
-
Hot water temperature monitor via extension kit
My heating system is the hot water storage type where a larger tank is used to store hot water for heating the radiators and hot water supplied via a heat exchanger. The tank is heated by a solar panel on the roof and a wood burning stove. Backup heating is via a gas boiler, which is controlled by Tado. It would be good if…
-
Feature To Assist With Balancing Radiators
Create a feature using the inbuilt thermometer in the radiator valves to work out order to balance radiators. It could work out time to temp for each radiator and advise you if there are any getting hotter slower/quicker.
-
Device grouping
Be able to group devices in to zones/areas Rather than having to turn all devices on if needed set a group for example downstairs/upstairs or whole house which would turn the grouped devices to the same settings
-
Auto valve calibration
I've occasionally noticed radiators getting warm when they should be off due to the valve needing recalibration. It would be useful if the valves periodically auto callibrated (which would also serve as an anti-seize function) or could auto detect if they temp was unexpectedly rising and trigger a calibration.
-
Geofencing by person
In a multi-person household, geofencing could be tailored so that one person leaving could adjust part of the house leaving the rest heated for those remaining inside. So if I go out, for example, the room I use most of the time could be left unheated, but other rooms still follow their usual schedule.
-
”Slow start” feature for less thermal stress
Opening the radiator valve fully with a cold system might cause unnecessary thermal stress on the system (and noise due to thermal expansion). Ramping up the valve for a short time might reduce the stress. I suggest a feature in line with “early start” called “slow start” to automatically ramp up the opening of the valve…
-
V3+ App Concept
I’ve created a concept of what our household, would like the V3+ app design to look like. Fonts, Icons, Size of Icons, Alignment, Heat Request & Set/Current Temperatures are just examples so may not be correctly placed or accurate. All just for representational purposes. I might add current room humidity to the tiles later…
-
Heating graphs on webpage
It would be really useful if the webpage could show the heating graphs that can be viewed on the phone app. It could also be useful to be able to download the graph data in some form.
-
Show battery status in the app
Would it not be possible to make the app do it's possible to see battery status. That's possible in other of my smart home units It's annoying that i can't see when it's time to put me battery in, so have to change often as i normalt travel very often when it's not Corona time
-
"Boiler-on" indicator on Home Screen
It would be helpful to have an easy way to tell if the boiler is being called upon or not - as it can affect radiators that do not behave independently and also help in understanding the general picture when it comes to fuel consumption. Currently, the only way to do this is to review each and every tile to see if any of…
-
Thread
Thread is the future of smart home connectivity and will also help people struggling with Tado range issues. Thread should also help grow network size without overwhelming the system as it becomes more resilient.
-
Temp/Humidity graph improvements
Please consider the following Temperature graph improvements... add increased resolution grid lines, ie. 1 degree and hourly coloured line showing set temperature join each 24hr section. No gap, same vertical grid resolution add to PC version app Thanks
-
Android & iOS Widget
Now that iOS also supports widgets, it would be useful to be able to have widgets on both Android and iOS phones so that you can set the temperature for a period of time. For example: Set the temperature in the widget to 23 degrees for 15mins
-
Scheduled "Call for heat"
atm we have the option to enable or disable a zone controller, and this stops the room calling for heat from the boiler. But, I think due to the cost of living crisis around the world atm, it would be a good option if Tado˚ could move this option to the Scheduling screen. My idea would be for each time block in the…
-
API Integration for Energy IQ
I use the energy provider Octopus In the UK, and they provide me with an API key for my account that can be used for getting meter readings and other things. It would be so good if, in Energy IQ, I could put in the API key so that the meter reading were added automatically.
-
Graphs
It would be nice to see the temperature and humidity or moisture content graphs on the web site as well as on the app
-
Support for multiple tado installations linked to 1 account
Please can we have proper support to enable management and control of multiple tado installations via the one account/email I stay at several locations and manage others as a landlord. When email notifications arrive they do not indicated which home they are for. Logging in/out of multiple accounts is awkward when you want…
-
Disable open window detection when heating switched off
The tado° app currently provides notification of open windows, even if all Smart Thermostats / Smart Radiator Thermostats are set to Frost Protection. This is clearly pointless, and just annoying. It would be better to only provide the open window notification when the thermostats are set to a temperature that might…
-
Allow additional schedules in addition to Home and Away
It would be great if it was possible to have additional schedules in Tado. I’d like if you were able to add additional schedules, such as “day shift” and “night shift” or “staycation”, so you can easily change schedules to meet your requirements. For example it I found i needed to change my normal schedule to account for…
-
No per month charge for automation (auto-assist) l
I do understand why push-notificatioms are free, but not why auto-assist is not. It seems like an important feature that should be included when Tado sells their products as automation and smart products. Why do I have to pay per month after I have bought the product? It kind of eats into the money (I might have) saved on…
-
allow changing the name of devices
Please allow us to change the names of devices to make it easier to identify them. For example, getting an email that tells me: "We have noticed that the batteries in your Smart Radiator Thermostat VA*******048 in the zone ****** are running low." I have 15 devices and if each device had a name I wouldn't have to waste…
-
Geofencing per room per person
My wife and I both work from home and have tado TRVs in our home offices. It would be useful if our individual rooms turned off heating when either of us leave the house. So if I’m still at home my room could stay heated but if my wife left the house the geofencing could detect that she was out and could turn the heating…