-
Mode that emulates a manual TRV behavior for Smart Radiator Thermostat
I wonder whether anyone else would find this useful: Problem: old leaky house that is unable to retain heat, potentially with mixed heating modes. Second problem. How to make best use of a boiler firing when zone is not expecting it. Solution: introduce 2 new modes for Smart TRVs - Passive and Passive Limited. The idea…
-
Internet Bridge with PoE
Would love to see the Tado Internet Bridge with Power over Ethernet. This could save us an additional cable because everything can be done with the Ethernet cable. Since the raspberry pi and many other similar devices can do it, this should be an easy task for Tado.
-
Support more than 10 rooms and 25 devices
Please can you add support for more than 25 devices and only 10 rooms, with a 5 bedroom house, with ensuites with a number of downstairs rooms, 25 devices is not enough when you want radiator TRVs and smart thermostats in each room. also limiting the total rooms to 10 does not work in this environment either. Please,…
-
[Released] Finer granularity of temperature reporting and adjustment for Smart Radiator Thermostats
Throughout the app temperatures are reported and set in units of whole degrees. It would be beneficial to increase the granularity of both reporting and setting to half degree increments.
-
Local API
Add an API server to the internet bridge (even if it requires newer, more powerful hardware) that supports controlling devices within the local network. Philips Hue provide a great example of how it can be achieved. My justification is twofold. Firstly, a local API can be accessed in the event of my internet going down.…
-
Support for Matter standards to allow full interop across Smart Home systems
Full support and integration with the Matter standards https://buildwithmatter.com as the standards develop and get published - ideally without having to upgrade the hub, etc.
-
Always show temperature on Tado ac
Have an option to set Tado ac to always show the current room temperature on display.
-
Zusammengeführt: Smart Ac control 10°C setting
Diese Diskussion wurde zusammengeführt.
-
[Released – ver. 5.10] Add back the "heating level" indicator in V3+ app
The indicator which displays the heating level (1, 2 or 3) has been removed from the V3+ app, this is a step backwards as this is a very useful indicator to show the status of the current system. Please add this indicator back.
-
Support 2 point calibration for adjusting temperature offset (Temperature Guesstimate)
It would be very helpful to enable 2 point calibration for adjusting the temperature measurement to match the middle of the room. Scenario as follows: At low temperature the thermostat reads the same as the temperature measured in the middle of the room e.g. 15°C so no offset required but at higher temperature the…
-
Allow swiping to access next room
Once you selected a room you should be able to just swipe to the next room but have to come out of the room to go back to the home screen and then select the next room; this is rather cumbersome and was much easier in the pre-v3+ app
-
Please implement the possibility of disabled the three LED lights of the internet bridge
Hi Everyone, the Tado internet bridge has three very bright LED lights. I would like to have the possibility to disable those LED lights please. A configuration as described below could be useful for all users: by default, after booting, the LED's are also on but in the app and/or the web portal you can choose to disable…
-
Show humidity as sensor in homekit
It’d be really useful to have the humidity from my tado devices show up as a sensor in homekit. This would allow me to add automations with other devices (eg when humidity goes above a certain level, turn on the dehumidifier)
-
Spring/Summer and Autumn/Winter settings
Depending on the time of year, I change the temp I want to heat rooms to. So around early April I adjusted things and will do so again in October. It would be useful to have a quicker way to jump between these two settings.
-
Activate open window detection with external window sensors
I would like to be able to use my window/door sensors to activate ‘open window detected’. This would be a great improvement as it will speed up this process and will keep ‘open window detected’ on until I close window/door. I know this can be done indirectly by setting the heater to “off” with ifttt but this means that it…
-
iPhone/Siri Shortcuts Support
TADO application doesn't appear in Siri/iPhone shortcuts. This application is very powerfull and, though complicated to use, can do much more than IFTTT in the Apple world. Tado must support Siri shortcuts. Homekit is obviously supported and a few (very limited) number of things can be done that way. Please support me.
-
Status of each thermostat valve position
Build a function into the settings menu where you can see the status of each thermostat, if the valve is open and how open it is. It would be nice, when you are troubleshooting.
-
Radio signal information
Show information about signal strength between each component and the bridge, so as to have an idea of where to put the bridge to improve the connection with the other components.
-
Expose official API and publish documentation
There are multiple home automation platforms available. Some of them make use of reverse engineered API and the main concern is such access would be blocked by Tado at some point or changed. Dear Tado, be brave! People like open products and your market share and brand rating would definitely grow with such API officially…
-
"Summer/Cooling mode" for wall thermostat
Hi there, I have an underfloor heating with a cooling function. In summer, cool water can run through the floor to cool the room. For that I currently need to set the temperature to max (25°C) to keep the thermostats open. If the room temperature would rise above 25°C the thermostats would close and prohibit a cooling…
-
[Release] OpenTherm Max Flow Temperature setting
On 28.10.2022 we have added the option to set the maximum flow temperature for OpenTherm configured tado thermostats / Extension Kits / Wireless Receivers without contacting our support department. From this moment forward, your installer will have the possibility to set the maximum flow temperature on V3/V3+ homes (your…
-
Improve Internet Bridge so it reconnects automatically
The Internet bridge often disconnects from the Internet leaving the Tado system unusable. Please improve its firmware so it reconnects automatically as every other IoT I have does. Currently, the only option is to power cycle which is unacceptable when it happens at 4am, and we wake up to a cold house....
-
Real window sensors from tado
We would like a real window / door sensor for the "window open function". The current detection of the open windows via the thermostats works so far quite well. However, we have discovered some problems. 1. In some rooms the detection of an open window does not work or does it too late (e.g. bathroom, room with balcony or…
-
Plot all rooms on same graph
Perhaps with selectors to show/hide rooms. Would be great to see the interaction between temperatures!
-
[released] Dark Mode Toggle Switch
Dark mode was just released. This thread now continues for the valid request to be able to toggle ON/OFF the dark mode regardless of the global settings on your phone. Original post: Mobile apps would look nice in Dark Mode. Reading the System OS Light/Dark theme option as default, then a toggle in settings if the user…
-
Add the heating level indicator 1,2,3 bars to the Home Screen in each room
For a quick overview of which rooms are currently heating it would be useful to see the three bars indicator for each room on the Home Screen.
-
Improve "Climate Report" graph
The horizontal grid lines in the "Climate Control" history graph currently behave very inconsistently and are not very clear to work out the temperature from. There are three fixed lines, the top and bottom have a label which varies depending on the range of the currently displayed graph, but by having fixed lines, this…
-
Support newer version of Worcester HT-BUS
I just upgraded from a worcester bosch greenstar cdi to a worcester bosch greenstar 8000 life. On my old boiler I could connect to the digital low voltage interface bus however the new boiler the ht-bus is not supported and I couldn't simply change over I had to rewire to the old relay style. The bus interface is better…
-
Improve heating algorithm to wind down heating power earlier, to prevent temperature overshooting
In using tado radiator valves and thermostat, I notice they almost always overshoot their intended temperature. That's usually because the heating power will remain at full strength almost until the temperature is reached. It would be better if the algorithm supports earlier wind down of the heating delivered so the…
-
Support one decimal place (0.1) for radiator valve temperatures in the Tado app
These devices appear to report their temperature at 1 decimal place of accuracy (I see it via the API in my Home Assistant integration) yet the Tado app only shows their temperature as integers. Can you please change this? I recognise this might be difficult on the device display itself but not in the app. I'd also like to…