-
Turn on heating without opening any SRVs
Hello all, I have Tado SRVs on all radiators in my home except for the two rads in the bathrooms wihch are always open. So whenever any SRV calls for heat, the bathroom rads also get heat. That's all fine and working as I want it to. I wanted to know if there's any way to turn the heating on so the bathroom rads get heat…
-
tado° support . . .
tado° support comes in for a lot of flack on this forum but I want to add a note of praise. I recently had a difficulty where the CH relay in my wireless receiver was ignoring switch off commands, especially when going from Boost to Switch off All Rooms. The HW relay continued to work correctly. I emailed…
-
"summer mode" to keep radiator valves open during summer
The problem is: If I connect all the smart radiator thermostats to my zone controller and I don't want to heat any room (because it is summer now) this results in all the radiators being 'closed' (or 'blocked'). This makes the total central heating system volume smaller (since the radiators are essentially cut off from the…
-
New Product: radiator fans
Hi, I'd like to make a suggestion to expand the Tado product line. In my country, the Netherlands, it's quite standard to have central heating, but a form of projecting this heat into a room (say, A/C etc.) is very rare. Studies show that placing fans on central heating radiators improve heat propagation into a room and…
-
Limit boiler output
As someone who has a Tado extension kit, wired into my boiler using Opentherm for modulating control, I'd love to have the option to limit the maximum output that tado can call for. Perhaps even on a room by room basis. The default is that tado will call for maximum output if the temperature of a room is quite cold.…
-
No hot water or heating
Hi, I moved the extender up in a cupboard (didn't unwire anything) but now nothing is working, the app says everything is connected, it's a traditional heating system, I'm not sure if something else has broken and it's a coincidence or what, I've reset the bridge, extender and the thermostat, I'm not sure what else to do.
-
How to turn off the LED light
After setting up, working fine, how can I turn off the led?
-
Multiple Boilers
Can Tado be installed to service two boilers in the same property. So two smart thermostats with hot water control and run from the same acct? Has anyone done this? Was thinking could setup each on a separate bridge but set each one up with the other powered off ?
-
Advice on smart wireless installation
Hi, I'm pretty much sold on picking up the Smart Wireless thermostat. I want to DIY install, but am after some advice before proceeding. I have a Honeywell ST6400C programmer (controlling central heating and an unvented cylinder), and I think the short story is that I will be replacing this with the wireless receiver.…
-
Créer un vrai thermostat
Bonjour, mon idée est assez simple, se servir du boîtier tado, qui prend la température, comme un thermostat, au lieu de laisser le climatiseur surfonctionner systématiquement.
-
Wireless control for underfloor heating
Dear tado community, I have a room with underfloor heating which currently is controlled via a manual control valve at the manifold (the manifold is located elsewhere in the building). I intend to replace the manual control valve with an electric actuator, which should be straightforward. However, since I have no cable…
-
Simple, automated monthly export
Hi I know there are various requests around data export, but could you not provide a simple option that enables a monthly export of the data? this is easy to add, could be fully automated and the data file sent to the account holder by email or via a more secure link where it can be downloaded for say 7 days. Tado is a…
-
Save(Export) and Load(Import) room settings
Hi. I really like the Tado system, but would it be possible that you can add a Save/load feature for the room settings. It would be great to be able to save a "winter" configuration, which has different timings and settings compared with a "autumn" set... for example, in autumn we would like to have 3 radiators turning…
-
Daikin heatpump, floor heating and tado
Good day everyone, I have a daikin altherma bluevolution 6kW heat pump for several months now, next to it I have a 300 liter storage tank. My house has 3 floors with radiators and underfloor heating. (1) ground floor : floor heating with temperature regulator knob and a tado thermostat (no tado heating knob). (2) 1st…
-
HomeAssistant entity control features missing after upgraded the tado firmware.
HomeAssistant entity control features missing after upgraded the tado firmware. Before: Tado: Firmware: 59.6 ------------------- After: Tado: Firmware: 118.3 After upgrading the Tado firmware, at Tado have a new feature of my ac: swag and it is working well. But At home assistant and HomeKit, all the control (Fan mode:…
-
Push hors domicile
Il est en général inutile de vouloir activé le mode "hors domicile" quand le chauffage est mis sur "hors gel"
-
Bridging BossTherm receiver
Hot water is perfect but I need to bridge the BR1 receiver to allow Tado to control heating. Any idiots guides. Still waiting on Tado getting back to me. There are only 4 wires going to the back of it two brown and two blue. How do I bridge these and what do I use to do it? Thank you
-
Wiring question
Hi, I have a Baxi Assure 30 currently wired to 2 Danfoss TPone thermostats. I am replacing them with tado v3 wired starter kit but the wiring points are different. I have N01 and N02 used in the current Danfoss controller but only seems to be N0 in the tado. The downstairs controller also controls the hot water system. Can…
-
Recommend Zoning Setback Temperature
As recommend by Tado and Heat Geek instead of going around the app setting what I think are good temperature differences per room - can there be a recommend setback temp that is variable depending on the temp I have set.
-
Schedule different to plan
Hi, brand new to this system. My App is showing the next change, to 18⁰ at 21:00, when I have set it to 5⁰ from midnight till 07:00. Programmed time to off is 21:00. Any idea where its picking up the 18⁰ from and how i change this? Is this some sort of default mode, do I need to add another time profile from 21:00 -00:00?
-
How to increase hot water temperature
My Tado wireless unit is newly installed. I am only getting lukewarm water from the hot water system. How to I get it back to the right temp (about 60 C)
-
Internet connections
I have two internet networks at home, one is Sky and the the other is Orbi. My question is if the network bridge is set up on one, does the receiver and all the TRVs etc need to be on the same network?
-
Manual change to hot water schedule
On the “Manual Control on Tado device” I have timer selected and set to 30 minutes but when I turn the hot water on for a boost it continues to the next schedule change. Is there something I am missing or a system wide problem. Thank you for any help.
-
No connection from smart radiator thermostat
Hi I have been trying for 3 days now to install the new Tado system onto our boiler. An electrician hand plumber have installed the kit and I’m trying to connect all the thermostats to the bridge. It’s not working. No pairing or EO or 3 lines as per instructions. We are stuck. Help is non existent from online chat. No…
-
Smart AC Control V3+ air purifier function
Hi, some air conditioners have an air purifier function. can you add this function? info : tekno point skiv air conditioner with the RA1A2 remote control
-
Smart AC Control V3+ sending the temperature measured by the Smart Thermostat to AC
some air conditioners have a function allowing the remote control to send the temperature it measures. with my tekno point skiv air conditioner with the RA1A2 remote control, the function is called "I FEEL button". could you integrate this functionality, so that the smart thermostat sends the temperature measured by the…
-
Allow heating of rooms that don't have a tado device installed.
I have some radiators without a TRV. Would be good to be able to heat them up i.e: turn on the boiler with the thermostat, but turn off all the other radiators that have tado Smart TRVs.
-
Internet is a must requirement for operation?
Hello. I have a few properties available for rent, but please note that some of them lack internet connectivity. However, I can use my phone's internet to download all the necessary software during installation. The key question is, is a reliable internet connection essential for day-to-day operations or not needed?
-
Newbie
Hi all, just installed a v3 package with hot water controls, can anybody explain what the purpose of the wireless wall thermostat is, as I understand it the wireless radiator valves control an individual room’s temperature.
-
IFTTT open window detection
Hi, Today the open window detection relies on a sudden temperature change I assume. It would be much better if it could be kicked off by IFTTT. That way, anyone with a Z-Wave or Zigbee alarm system could send an alert to Tado to trigger open window and stop it when the window is closed. Would also be great if if could work…